Register to reply 
Falling to Earth 
Share this thread: 
#1
Oct913, 05:55 PM

P: 3

I'd like to graph the function of and object falling to earth from a point high enough that air density has an effect on the rate the object falls due to gravity. I'm not really sure where to start though.
I'm thinking about that guy that jumped from the highest point ever freefalled from and broke the sound barrier. 


#2
Oct913, 09:55 PM

Emeritus
Sci Advisor
HW Helper
Thanks
PF Gold
P: 6,334

First, figure out what function you are talking about. Velocity versus time? distance versus time?



#3
Oct913, 11:00 PM

P: 3

What do you think would best show the change in gravity due to the change in air resistance against an object?
I was thinking that I'd have to first find an equation for the amount of air at different altitudes. Then calculate the level of air resistance and apply it to the amount of air equation. Then figure out how that applies to gravity at different altitudes. I hope that helps clear up what I'm getting at. 


#4
Oct1013, 12:12 AM

Emeritus
Sci Advisor
HW Helper
Thanks
PF Gold
P: 6,334

Falling to Earth
It's not clear what you mean by 'the change in gravity due to the change in air resistance against an object'.
You should review Newton's Law of Gravitational attraction: F = Gm1m2/r^2 


#5
Oct1013, 01:14 AM

P: 3

I believe he is talking about rate of descent and the effect varying atmospheric densities would have on a falling object of something like the size of a person. So that rate of descent would become variable due to the area resistance would be placed upon.



#6
Oct1013, 04:11 AM

Emeritus
Sci Advisor
HW Helper
Thanks
PF Gold
P: 6,334

Eventually, a terminal velocity should be reached when the weight of the body balances the drag force.



#7
Oct1013, 08:10 AM

Mentor
P: 11,626

The terminal velocity depends on the density of the medium (air). An object falling from a very great height would first reach a rather high terminal velocity corresponding to the low density of air at high altitude. As it falls into denser air, the terminal velocity decreases. To put it another way, the object's drag coefficient increases with air density.
If the drag coefficient is constant, it's possible to solve the differential equation of motion exactly for certain cases. With a variable drag coefficient, you'd have to solve the differential equation numerically. 


#8
Oct1013, 10:09 AM

P: 3

At extreme heights there's less gravity. A falling person would fall slower, but there's less air resistance at those heights, so a person would fall faster. The guy that did a free fall from 128,100 ft broke the speed of sound. I'd like to calculate the change in speeds he fell and view it on a graph. I'd imagine he broke the speed of sound but slowed down as he got closer to earth.
I'd also like to know if he slowed down to the standard terminal velocity eventually. 


#9
Oct1013, 10:14 AM

P: 1,008

Drag force increases with air density (all else equal), but not drag coefficient. 


#10
Oct1013, 11:31 AM

Mentor
P: 15,067

You can come fairly close assuming a constant coefficient of drag and gravity that decreases linearly with altitude:
[tex]F(h) = \frac 1 2 \rho(h) v^2 C_dA  mg(h)[/tex] Here, h is the person's altitude. I'll use meters rather than feet and force is a signed quantity (not a vector; I'm only looking at the "falling straight down" problem here). A negative value means the person is accelerating downward, positive means upward. The first part is drag to air resistance. The term ρ(h) is the density as a function of altitude. You'll need some model of air density. I'd suggest using the 76 US Standard Atmosphere model. It's fairly simple, something you can easily implement in a spread sheet or simple computer program. Unfortunately, you might have to wait a few days to get your hands on that model. You might be able to find it with some good internet searching. The US government websites where you would normally find it are down right now The final part of that term, C_{d}A, is the (unit less) coefficient of drag times the cross section to drag. It might be easier to make this one item rather than two in your model. If you do this, try using 1 square meter as a first cut. The final term is just gravitational force. A simple linear model of gravitational acceleration g(h) will work quite nicely for this problem. The linear term is called the "free air correction". Subtract 3.084×10^{6} m/s^{2} for every meter of altitude from the ground level gravitational acceleration. For New Mexico, I'd suggest using (9.796 3.084×10^{6}h) m/s^{2}, where height h is in meters. 


#11
Oct1013, 11:38 AM

Thanks
P: 5,687




#12
Oct1013, 12:33 PM

P: 1,425

Drag coefficient may be dimensionless but it does vary with speed, density, and viscosity of the medium. Drag coefficient can be plotted against another dimensionless number called the Reynold`s number which incorporates velocity, dynamic viscosity, density and a characteristic length. One can use kinematic viscoscity in favour of density and dynamic viscoscity. In addition, temperature of the medium will also affect the viscosity, and for gases the kinematic viscosity will increase with temperature. As the speed of the object increases through the medium particular flow seperation points are reached which will change the coefficient of drag. The range of CD will vary from attached laminar flow at slow speeds, where the coefficient can be quite high ( > 1.0 ), to that at detached turbulent flow where it can be much lower. 


#13
Oct1313, 01:30 PM

P: 1,008




Register to reply 
Related Discussions  
Falling through the Earth problem  Introductory Physics Homework  9  
Mass falling in Earth's Gravity... help  Introductory Physics Homework  9  
Falling down a hole through the Earth.  General Physics  18  
Falling through the earth  Introductory Physics Homework  7  
Ball falling through hole in the earth.  General Physics  17 