
#1
Jun2813, 08:02 AM

P: 6

Hi everyone,
I am curious as to whether it is possible to calculate the difference in density due to applied (mechanical) stress on an object. E.g.: apply a controlled force of, say, 50 N on a structure, calculate the mechanical stress in the object with sigma = M/I * z and then go on from there, using some kind of relationship between stress and density to figure out how density changes throughout the object... Looking forward to an answer, if there is one ;) Thank you very much! Best regards, Marc 



#2
Jun2813, 08:31 AM

Sci Advisor
PF Gold
P: 11,383

Welcome to PF
The compressibility of a substance is discussed here Everything is compressible but solids and liquids are a lot lot less compressible than gases. 



#3
Jun2813, 08:33 AM

P: 6

where?




#4
Jun2813, 08:34 AM

Sci Advisor
PF Gold
P: 11,383

relationship between stress and density
HAha  click on the blue "here".




#5
Jun2813, 08:35 AM

P: 6

that link was not there when I first loaded the page.




#6
Jun2813, 08:38 AM

HW Helper
Thanks
P: 5,581

In a nutshell, no, there is no relationship between bending stress and the change in density of an elastic structure.
I am curious as to what prompted this question in the first place. 



#7
Jun2813, 08:42 AM

P: 6

Hi,
we are working on a problem involving stressinduced birefringence... since the dielectric constant of a substance can be put in relation with its density (ClausiusMossotti relation) it would have been interesting to be able to link a "change in density" due to stress to a change in the dielectric constant... I guess, however, we'll have to look for another way! But thank you very much! 



#8
Jun2813, 09:18 AM

Sci Advisor
PF Gold
P: 11,383

Just a thought. As the compressibility of solids is so high, would it not be more likely that a dielectric material, when deformed by a force, would assume a shape which would maintain the density, ( i.e. virtually unchanged) as it changed shape? I am not into Materials Science really but it would seem a reasonable assumption.
(I pressed the 'go' button on my first post before I was ready) 



#9
Jun2813, 09:58 AM

HW Helper
Thanks
P: 5,581

Photoelasticity also uses birefringence of materials to show the distribution of stresses within the material as it is loaded.
See: http://en.wikipedia.org/wiki/Photoelasticity I think the CM formula involves the density of a material, not the change in density. Are you saying that the dielectric constant a material isn't a constant? 



#10
Jun2813, 10:37 AM

P: 6

@SteamKing
given birefringence and from Maxwell's eqn. with [itex]\mu[/itex]≈1 and ε_{r}=n^{2} I am trying to use the CM formula to compute the refractive index given a volume change due to a force applied on the structure/object... I'll work on it and see if it fits the experimental data... Thank you for your help! Marc 



#11
Jun2813, 11:20 PM

Sci Advisor
HW Helper
Thanks
PF Gold
P: 4,502

Using the 3D tensorial form of Hooke's law involving the Young's modulus and the Poisson ratio, one can calculate the change in density of a linearly elastic solid material under prescribed loading.



Register to reply 
Related Discussions  
The relationship between StressEnergy tensor and Mass  Special & General Relativity  8  
3D stress strain relationship  Mechanical Engineering  4  
Energy Stress Relationship  Mechanical Engineering  2  
Relationship between thermal stress and vibration of a material  General Physics  0  
Constitutive Law (stressstrain relationship) of maxwell material  Classical Physics  1 