Calculating Energy Flux Density and Candle Power

In summary, the standard candle has a radiant intensity of 1/683 W/sr and the unit of measurement is watts per steradian. The solid angle of an entire sphere is 4π and there are 4π steradians in a sphere. To calculate the energy flux density at a distance of 1.06 meters from the candle, we can use the formula watts/steradian. For the candle power of a 75 watt light bulb, we can assume it emits uniformly into 4π steradians and use the formula Watts per square meter. However, the units in photonics can be complex and not always based on powers of ten.
  • #1
Ryo124
101
0

Homework Statement



A standard candle has radiant intensity equal to 1/683 W/sr.

[The unit of measurement is watts per steradian. The steradian (sr) is the standard unit for solid angles: If a patch on the surface of a sphere of radius r has area A, then the solid angle subtended by the patch at the center of the sphere is A/r^2. The solid angle of an entire sphere is 4π because the area is 4πr^2.]

a) What is the energy flux density (power per unit area) at a distance of 1.06 meters from the candle?

b)What is the candle power of a 75 watt light bulb?

Homework Equations



I figured out the power to be 1.84E-2 W

The Attempt at a Solution



I'm not sure how to solve this one.
 
Physics news on Phys.org
  • #2
There are 4pi sterads in a sphere.
How many m^2 are there in a sphere of radius 1.06m
So you can work out how many m^2 / sterad.

a, You know the watts / sterad so getting w/m^2 is easy.

b, just assume the bulb emits uniformaly into 4pi sterads.
 
  • #3
As it says in the querstion the part of the surface area of a sphere that is subtended by a steradian is r^2.

As it says in the question the light energy passing through this area is 1/683 (weird!) Watts and r is 1.03 m.

The answer required is Watts per square meter. We have the Watts and we have the square meters (so it's not necessary to calculate the total power of the candle) ...
 
Last edited:
  • #4
Thanks again mgb and catkin as well, I got them both.
 
  • #5
catkin said:
As it says in the question the light energy passing through this area is 1/683 (weird!)...

No stranger than 1 horsepower = 746 Watts: many widely used physical units substantially predate the introduction of the metric system and, later, SI. (There's a ton [ = 907 kg.] of such units in fields like engineering or astronomy...) The metrical congresses standardized the relationship of these units to the metric system, but often failed in efforts to replace them with something that's a nice power of ten. (There's still debate on questions like whether astronomers should keep using light-years or parsecs instead of something that's just 10^13 m long...)
 
Last edited:
  • #6
The 683 is to match the eye's response and is based on an early unit.
Defined "as the light produced by a pure spermaceti (sperm whale oil) candle weighing one sixth of a pound and burning at a rate of 120 grains per hour."
The new metric Candela is even worse = "luminous intensity of a blackbody at the freezing point of liquid platinum which was to be 58.9 international candles per square centimeter."

Add in lumens/lux/EV and a bunch of other units and photonics is a pain. Usually end up working either in photons/sec or watts/sec.
 
  • #7
mgb_phys said:
... the light produced by a pure spermaceti (sperm whale oil) candle weighing one sixth of a pound and burning at a rate of 120 grains per hour ...
Wonderful!
 

1. What is energy flux density?

Energy flux density, also known as irradiance, is a measure of the amount of energy per unit area that is radiated from a source in the form of electromagnetic radiation. It is typically measured in watts per square meter (W/m²).

2. How do you calculate energy flux density?

To calculate energy flux density, you need to know the total amount of energy emitted by a source and the surface area that the energy is being emitted over. You can then divide the total energy by the surface area to get the energy flux density in watts per square meter (W/m²).

3. What is candle power?

Candle power is an outdated unit of measurement for the amount of light emitted by a source. It is defined as the amount of light output by a standard candle from a distance of one foot. It has since been replaced by the more accurate unit of measurement, the lumen.

4. How do you convert candle power to energy flux density?

To convert candle power to energy flux density, you can use the conversion factor of 12.57 lumens per watt. Multiply the candle power by 12.57 to get the equivalent energy flux density in lumens per watt (lm/W). You can then convert lumens per watt to watts per square meter (W/m²) by multiplying by the surface area of the light source in square meters.

5. Why is it important to calculate energy flux density and candle power?

Calculating energy flux density and candle power is important for understanding the amount of energy and light emitted by a source. This information can be useful for designing lighting systems, determining energy efficiency, and evaluating the potential impact on the environment. It is also important for comparing different light sources and making informed decisions about which one to use in a given situation.

Similar threads

  • Introductory Physics Homework Help
2
Replies
35
Views
3K
  • Introductory Physics Homework Help
Replies
13
Views
2K
  • Introductory Physics Homework Help
Replies
31
Views
4K
  • Introductory Physics Homework Help
Replies
23
Views
2K
  • Electromagnetism
Replies
28
Views
2K
  • Introductory Physics Homework Help
Replies
2
Views
715
  • Introductory Physics Homework Help
Replies
12
Views
3K
  • Astronomy and Astrophysics
Replies
4
Views
2K
  • Introductory Physics Homework Help
Replies
10
Views
1K
  • Electrical Engineering
Replies
8
Views
899
Back
Top