Laser light vs. synchrotron light in ARPES measurements

In summary, ARPES measurements show that synchrotron light has a higher brightness and can cover a wider area of momentum space compared to laser light. This is because the transition matrix element for laser light restricts the allowed transitions due to the negligible linear momentum it imparts, while synchrotron radiation has a much higher brightness and can reach higher momentums. Efforts are being made to develop x-ray free electron lasers to combine the advantages of both laser and synchrotron light.
  • #1
vatlychatran
25
0
In ARPES measurements, people say that the laser light cannot cover a wide area of momentum space whereas the synchrotron light can (M. Hashimoto et al., Nat. Phys. 10 (2014) 483). Why is that?

(Figure 3a in the paper is a combination of laser and synchrotron data to plot spectra along the Fermi surface from the nodal region to the antinodal region)
 
Physics news on Phys.org
  • #3
At a glance it looks like they have a "psuedo" band gap .

Since the laser imparts negligible linear momentum, the laser excited electron from below to above the band gap must have the same linear momentum. This is because the transition matrix element (going back to Fermi's rule here)

<psi(k_initial,E_initial)|laser|psi(k_final,E_final)>

is always zero except when k_initial = k_final. This restricts the allowed transitions, and is especially noticeable for single crystals.

The core states excited by x-rays in ARPES experiments are a linear combo of momentum eigen states. That is the transition matrix element

<psi(k_core,E_core)|laser|psi(k_final,E_final)>

will always be none zero because psi(k_core,E_core) has a component along almost every possible final state.
 
  • #4
The maximum momentum you can reach is k=2 pi/lambda, where lambda is the wave length of the light.

Laser light is typically visible with wave lengths of 300 nm and above, synchrotron "light" is typically soft or hard x-rays, i.e. wave lengths of 20 Angstroms or less.

Brightness has nothing to do with this. In fact, lasers have much higher brightness than synchrotrons. There is a lot of work going on these days on developing x-ray free electron lasers to get the best of both worlds.
 
  • #5
Thank you
 

What is the difference between laser light and synchrotron light in ARPES measurements?

Laser light and synchrotron light are two different sources of light used in ARPES (Angle-Resolved Photoemission Spectroscopy) measurements. Laser light is a monochromatic and coherent source of light, while synchrotron light is a broad spectrum and incoherent source of light. This difference in properties affects the type of information that can be obtained from ARPES measurements.

Which source of light is better for ARPES measurements?

Both laser light and synchrotron light have their advantages and disadvantages in ARPES measurements. Laser light offers a higher energy resolution and can be easily focused on a small spot, allowing for precise measurements. On the other hand, synchrotron light provides a broader energy range and higher photon flux, allowing for faster measurements and the ability to study a larger area of the sample.

Can laser light and synchrotron light be used together in ARPES measurements?

Yes, laser light and synchrotron light can be used together in ARPES measurements to obtain complementary information. For example, laser light can be used to study the electronic structure of a specific energy range, while synchrotron light can be used to study a broader energy range.

How does the penetration depth of laser light and synchrotron light differ in ARPES measurements?

The penetration depth of laser light and synchrotron light is another important factor to consider in ARPES measurements. Laser light has a shorter penetration depth, meaning it can only probe the surface layer of the material. In contrast, synchrotron light has a longer penetration depth, allowing for the study of the bulk properties of the material.

Are there any other sources of light that can be used in ARPES measurements?

Besides laser light and synchrotron light, other sources of light such as LED (Light-Emitting Diode) and X-ray tubes can also be used in ARPES measurements. However, these sources may have limitations in terms of energy range, intensity, and energy resolution compared to laser light and synchrotron light.

Similar threads

  • Astronomy and Astrophysics
Replies
19
Views
4K
  • Mechanical Engineering
Replies
1
Views
2K
  • Beyond the Standard Models
Replies
2
Views
2K
Replies
1
Views
1K
  • Beyond the Standard Models
Replies
11
Views
2K
  • Astronomy and Astrophysics
Replies
8
Views
4K
Replies
89
Views
34K
  • MATLAB, Maple, Mathematica, LaTeX
Replies
8
Views
3K
  • Beyond the Standard Models
Replies
24
Views
7K
Back
Top