Is Cross Bonding Necessary in Multi-Leaf Concrete Block Retaining Walls?

In summary, the owner was disappointed with the lack of cross bonding between the leaves of the stream retaining wall being built by the contractor. The lack of cross bonding may lead to delamination and eventual failure of the wall.
  • #1
Studiot
5,440
9
There are quite a few canalised streams in my area and I was watching one riparian owner's contractor rebuilding his stream retaining walls.

The top 2 metres of these walls were being constructed in 225 (9") dense concrete blockwork, three leaves thick making a total wall thickness of 675 width of wall.

Watching the work I said to the owner "Is there going to be any cross bonding between the leaves?"
I didn't see any, nor did I see any ties being installed.


Comments by budding Civil Engineers?
 
Engineering news on Phys.org
  • #2
Disappointing lack of response there was a learning opportunity here, especially if certain contractor's brickies are members of PF.
 
  • #3
Cross bonding between the three leaves will increase the strength and robustness of the walls, but whether it's necessary depends on how the wall is intended to function.

If it is designed solely as a mass structure, cross bonding the leaves will have no effect. If it's designed to resist bending, cross bonding will increase its strength if the individual leaves would otherwise "delaminate" under lateral load, for example, if the perpends between the leaves were not being filled with mortar as the work progresses. If there is sufficient "mortar bond", cross bonding will not add anything at normal working stresses, but would probably add something as failure approached.

The other aspect is accidental damage. If the "stream face" was potentially subject to damage from floating objects, an unbonded leaf would be much easier to remove and replace than a cross-bonded one.

It's horses for courses really - have to wait and see what happens to it I guess!
 
  • #4
Welcome to Physics Forums Bpseco.

Cross bonding is needed to transfer shear to make the three leaves act as one mass in a gravity retaining wall.
If the ground behind the wall becomes active the inner two leaves will simply add to the load on the outer leaf, rather than working in conjunction with it.

go well
 
  • #5
what are the ground conditions?
does not sound like a great idea to me to use 3 skins of block with no ties every 3 courses. In fact if I was constructing it out of block I would use expamet brick mesh in the courses and fully tie the leaves together so that they all act as one mass thus achieve the min. wall thickness required to resist the soil active Earth pressure and other lateral loading/surcharge/water pressure etc
what was below the block? RC wall?
have they put on any finishes lower down yet? waterproofing etc..?
 
  • #6
How do ties transfer shear?

Surely all the do is stop the walls separating?
 
  • #7
the ties won't help with shear transfer they will just all a modicum of continuity between the layers of blockwork.
You would need dowel bars to transfer the shear..
BS 8002 (Earth retaining structures) only allows unreinforced masonry walls up to 1.5m high without the need for buttressing or steps.
 
  • #8
the ties won't help with shear transfer

Yes indeed, so ties are no substitute for proper cross bonding.

Of course the wall could have been post tensioned, or even just tied, to Earth anchors, but they weren't.
 
  • #9
yes I was going to say the 2m span for unreinforced concrete block is a little risky. overturning and sliding are jumping out at me right now!

Proper cross bonding would have been preferable always - that way at least you have a honeycomb x-section and 'proper' stiffness in both planes and there would be no delamination.

Still RC is always the preference of choice, at least for the majority of work I do
 
  • #10
No sheet piling then?
 
  • #11
Incidentally I should say welcome to Physics Forums, there's plenty of room for structural engineering experience here.

The annual round of high school balsa wood bridge design will soon be in full swing.

:biggrin:

Have you explored the learning materials section of PF?

https://www.physicsforums.com/showthread.php?t=155389
 
  • #12
It has been awhile since I last designed any sheet piling - usually a contractor job that one.
I am familiar with the theory behind retaining wall design, we do a fair amount of underpinning and retaining walls in the office. The learning material section looks good though, concise and clear.

Ah good stuff, I do like a bit of truss design. I believe I built one myself a long time ago as an undergrad. Balsa wood compression members and steel wound wire tension bottom chord, worked a treat for point loads at the apex points of the truss.

Now if anyone fancies designing a steel beam to span 9m with 150 RC planks spanning into it with a loading width of 3m along with 5m line load of 3m high masonry and a couple of point loads from incoming beams, all this whilst limiting deflection to span/360 it would be most appreciated and ideally section depth to 305UC max! :)
what a fun evening ahead
 
  • #13
we do a fair amount of underpinning

I do remember, some years back, doing a specialist underpinning project on an ancient monument, in the middle of a Water Authority scheme to rebuild a section of river walls.

The WA Engineer, an old boy about to retire, said to me "you can't beat mass concrete in water engineering".

go well
 

What is civil - structural engineering?

Civil - structural engineering is a branch of engineering that focuses on the design, construction, and maintenance of structures such as buildings, bridges, roads, and dams. It involves the application of physics, mathematics, and materials science to create safe and functional structures that can withstand various loads and environmental conditions.

What are the key responsibilities of a civil - structural engineer?

A civil - structural engineer is responsible for designing, analyzing, and ensuring the safety and integrity of structures. They also oversee the construction process, conduct inspections, and make modifications or repairs as needed. Additionally, they may be involved in project management, budgeting, and collaborating with other professionals.

What skills are necessary for a career in civil - structural engineering?

Some essential skills for civil - structural engineers include strong analytical and problem-solving abilities, proficiency in computer-aided design (CAD) software, knowledge of relevant codes and standards, teamwork and communication skills, and attention to detail. They should also have a solid understanding of materials, structural mechanics, and construction processes.

What are the steps involved in a typical civil - structural engineering project?

A civil - structural engineering project typically involves several steps, including site investigation, conceptual design, detailed design, construction planning and management, and monitoring and maintenance. The engineer will gather information about the site and its surroundings, determine the project's objectives and constraints, develop design options, and create detailed plans and specifications for construction. After completion, the engineer may also conduct inspections and assessments to ensure the structure's longevity and safety.

What are the current challenges in the field of civil - structural engineering?

Some of the current challenges in civil - structural engineering include the need for sustainable and environmentally friendly design, the use of new materials and technologies, and the aging of existing infrastructure. Engineers also face challenges related to budget constraints, safety concerns, and meeting the demands of a rapidly growing population. Additionally, there is a growing emphasis on incorporating resilience and disaster preparedness into structural design to mitigate the effects of natural disasters.

Hot Threads

Recent Insights

Back
Top