Enthelpy of Combustion - Alkanes

  • Thread starter salman213
  • Start date
  • Tags
    Combustion
In summary, the conversation discusses the enthalpy of combustion for alkanes, specifically CH4(g) (methane) reacting with O2(g) to form CO2(g) and H2O(l). The standard heats of formation for each compound are also given. The question then asks to calculate the difference in enthalpy and internal energy for the combustion reaction of 1 mole of methane, assuming standard state conditions and 298 K for all reactants and products. The balanced equation for the reaction is CH4(g) + 2O2(g) ---> CO2(g) + 2H2O(l). The ideal gas law must be used, but the incremental change in volume due to liquids is neglected. The
  • #1
salman213
302
1
Enthalpy of Combustion -- Alkanes

Write a balanced equation for the combustion of CH4(g) (methane)
(its reaction with O2(g) forming the products CO2(g) and H2O(l)).

Given the following standard heats of formation:
[tex]\Delta[/tex]Hf° of CO2(g) is -393.5 kJ/mol
[tex]\Delta[/tex]Hf° of H2O(l) is -286 kJ/mol
[tex]\Delta[/tex]Hf° of CH4(g) is -74.8 kJ/mol

Calculate the difference, [tex]\Delta[/tex]H-[tex]\Delta[/tex]E=[tex]\Delta[/tex](PV) for the combustion reaction of 1 mole of methane.
(Assume standard state conditions and 298 K for all reactants and products.)


-----------------------------------------------------------------------------------
The ideal gas law must be used.
The incremental change in volume due to liquids is neglected (cf the volume of 1 mole of H2O(l) is 18 mL, whereas the volume of 1 mol of a gas at 298 K is about 24,450 mL.
Be careful to account for the total change in number of moles of gas molecules (be sure the signs and units are correct too).
Note that certain alkanes are gases in the standard state.

-----------------------------------------------------------------------------------


My balanced equation was CH4 (g) + 2O2 (g) ---> CO2 (g) + 2H2O (l)

it says use PV=nRT but i was confused about the change in moles like is it just the change in moles of the GASES so molesfinal - molesininitial = 1 - 3 = -2 ?
and then
(-2)(0.08206)(298) = the difference...?

but i think that's wrong!
 
Last edited:
Physics news on Phys.org
  • #2
The number of moles doesn't change - for each mole of CH4 and two moles of O2, one mole of CO2 and 2 moles of H2O are produced. If the reactants start at STP, the products would certainly not, but the problem states
(Assume standard state conditions and 298 K for all reactants and products.)
but, think about the fact that one is given H2O (l) as opposed to H2O (g), which would occupy a greater volume. Compare the volume of liquid water to vapor.
 
  • #3
huh? sorry i don't really understand what i need to compare..

'The incremental change in volume due to liquids is neglected (cf the volume of 1 mole of H2O(l) is 18 mL, whereas the volume of 1 mol of a gas at 298 K is about 24,450 mL. "

i thought volume didnt matter since it was neglected :S
 

What is enthalpy of combustion for alkanes?

The enthalpy of combustion for alkanes is the amount of heat released when one mole of the alkane undergoes complete combustion in excess oxygen. It is a measure of the energy stored in the chemical bonds of the alkane.

How is the enthalpy of combustion for alkanes calculated?

The enthalpy of combustion for alkanes can be calculated using the formula: ΔH°comb = Σ(H°f,products) - Σ(H°f,reactants), where ΔH°comb is the enthalpy of combustion, Σ(H°f,products) is the sum of the standard enthalpies of formation for the products, and Σ(H°f,reactants) is the sum of the standard enthalpies of formation for the reactants.

What factors can affect the enthalpy of combustion for alkanes?

The enthalpy of combustion for alkanes can be affected by the type and number of carbon and hydrogen atoms in the alkane, as well as the temperature and pressure at which the combustion occurs. Impurities in the fuel can also affect the enthalpy of combustion.

What is the significance of enthalpy of combustion for alkanes?

The enthalpy of combustion for alkanes is an important measure in determining the energy content of fuels. It is also used in the design and optimization of combustion processes, such as in engines and power plants. Additionally, it can provide insight into the environmental impact of burning different types of fuels.

How does the enthalpy of combustion for alkanes compare to other types of fuels?

The enthalpy of combustion for alkanes is generally higher than that of other types of fuels, such as alcohols or carbohydrates. This is because alkanes have more carbon-hydrogen bonds, which are stronger and release more energy when broken during combustion. However, the specific enthalpy of combustion can vary depending on the specific alkane and the conditions of combustion.

Similar threads

  • Biology and Chemistry Homework Help
Replies
4
Views
1K
  • Biology and Chemistry Homework Help
Replies
13
Views
3K
  • Mechanical Engineering
Replies
2
Views
193
  • Biology and Chemistry Homework Help
Replies
11
Views
1K
  • Biology and Chemistry Homework Help
Replies
7
Views
2K
  • Biology and Chemistry Homework Help
Replies
7
Views
2K
  • Biology and Chemistry Homework Help
Replies
4
Views
6K
  • Biology and Chemistry Homework Help
Replies
22
Views
3K
  • Biology and Chemistry Homework Help
Replies
10
Views
3K
  • Biology and Chemistry Homework Help
Replies
3
Views
5K
Back
Top