What type of digital signaling is more efficient, digital DC or digital AC?

In summary: No, the "phase angles" will remain stable as long as the sampling rate is matched to the A/C frequency.
  • #1
Bararontok
298
0
What type of digital signaling is more efficient, digital DC or digital AC?

With digital DC, the square-wave signal is only between a (+) value and 0.

With digital AC, the square-wave signal is between a (+) & (-) value.
 
Computer science news on Phys.org
  • #2
The thread originator is requesting an answer to the question.
 
  • #3
Bararontok said:
What type of digital signaling is more efficient, digital DC or digital AC?

With digital DC, the square-wave signal is only between a (+) value and 0.

With digital AC, the square-wave signal is between a (+) & (-) value.

Without more context to the question, the answer is that they are the same.
 
  • #4
Can you define efficient?
 
  • #5
skeptic2 said:
Can you define efficient?

Which digital signalling method listed in post #1:

-Uses electronics that is less complex and prone to malfunction
-Is less error prone
-Uses less electrical energy
-Can operate at higher data rates
 
  • #6
Bararontok said:
Which digital signalling method listed in post #1:

-Uses electronics that is less complex and prone to malfunction
DC - Most logic devices are unipolar.

-Is less error prone
One measure of immunity from errors involves the amount of difference between a 1-level and a 0-level. If the difference between the levels for AC and DC transmission is the same, the immunity from errors should be the same.

-Uses less electrical energy
I'm assuming you mean uses less electrical energy for the same bit error rate. I'm not sure there's a difference.

-Can operate at higher data rates
I can't think of any reason there would be a difference. In my experience more efficient signalling methods involve more efficient coding algorithms rather than relying on AC or DC.

DC has the disadvantage of not being able to pass through capacitors or transformers. This may be important if bandpass filters are used to reduce noise.
 
  • #7
skeptic2 said:
DC has the disadvantage of not being able to pass through capacitors or transformers. This may be important if bandpass filters are used to reduce noise.

What if the DC is a fluctuating DC? A constant DC cannot pass through a capacitor in series because once the capacitor is fully charged, it can no longer permit current flow, but in a fluctuating DC, the capacitor has time to discharge its stored energy when the power is cut off.

In the case of a transformer, is a fluctuation in current enough for the primary inductor to emit radiation that can be absorbed by the secondary transformer or is a reversal of polarity necessary?
 
  • #8
With both capacitors and transformers the fluctuation of the DC, which will include both data and noise, will pass through, but the DC bias will not. At that point we can no longer call it a DC transmission method.
 
  • #9
That is correct since the DC bias comes from a constant DC power supply while the fluctuating DC signal is a separate component.
 
  • #10
If the orignal post means digital signals used in common integrated circuits, then most logic just uses some positive voltage and zero voltage for the two states. Decades ago, computers like the HP 2100 mini-computer used +5, -2 volts for it's TTL logic on it's circuit boards.

Interfaces like USB send synchrounous (fixed clock rate) data via a differential pair of signals, +D and -D, where -D is an inversion of +D, each with a 3 volt range. There are also ground and +5 volt pins, which the host drives to send power to some USB devices. Wiki article:

http://en.wikipedia.org/wiki/Usb

Interfaces like RS-232 can range from +/- 3 volts to +/- 15 volts, and for the original PC, +/- 12 volts was used for RS-232. There is a ground pin used as a reference for 0 volts. Wik article:

http://en.wikipedia.org/wiki/RS_232
 
  • #11
Won't the "phase angles" of a sampled A/C become random unless your sample rate is matched to the A/C frequency?
 

1. What is the difference between digital DC and digital AC signaling?

DC (direct current) signaling is a type of digital communication where the signal is constantly at a steady voltage level, while AC (alternating current) signaling is a type of digital communication where the signal fluctuates between positive and negative voltage levels.

2. Which type of digital signaling is more commonly used?

Digital AC signaling is more commonly used because it allows for longer distance communication and is less susceptible to interference.

3. Is there a significant difference in efficiency between digital DC and digital AC signaling?

In terms of efficiency, there is not a significant difference between the two types of signaling. However, digital AC signaling is more efficient for long distance communication.

4. Can digital DC and digital AC signaling be used together?

Yes, digital DC and digital AC signaling can be used together in certain applications. For example, digital AC signaling can be used for long distance communication and then converted to digital DC signaling for closer range communication.

5. Which type of digital signaling is better for noise immunity?

Digital AC signaling is better for noise immunity because the signal is constantly changing, making it more difficult for outside interference to affect the communication.

Similar threads

Replies
15
Views
1K
  • Engineering and Comp Sci Homework Help
Replies
8
Views
1K
Replies
9
Views
1K
  • Computing and Technology
Replies
2
Views
1K
Replies
1
Views
844
  • STEM Educators and Teaching
2
Replies
40
Views
2K
  • Electrical Engineering
2
Replies
48
Views
2K
  • Computing and Technology
Replies
2
Views
1K
Replies
1
Views
1K
  • Electrical Engineering
Replies
13
Views
1K
Back
Top