Register to reply 
Bragg and Brillouin diffraction 
Share this thread: 
#1
Apr1314, 12:58 AM

P: 106

I'm supposed to give a seminar tomorrow for my 300 level experimental physics paper. The experiments we do our reports on are predetermined and I pulled the short straw with the most bloody complicated on here, the acoustooptic modulator. I'm trying to get my head around it and i've spend the good part of the day and not gotten very far. I understand that you require constructive interference to produce the maxima and due to the varying refractive indices of the material we will get a weird equation. But the equation we are given is
sin (θ) = λ/2nd Where θ the bragg angle, d is the wavelength of the sound wave in the acousto optic modulator. So it seems odd to me firstly how are the multiple maxima produced when the light in angle must equal the light out angle shouldn't that just produce on maxima. Secondly how can we just chuck n in for the quoted refractive index of the crystal when this varies at every point. How the hell is this equation derived specifically for brillouin scattering. There are no good sources of this on the internet. Please help, thanks. 


#2
Apr1314, 04:54 AM

Sci Advisor
P: 3,593

You are doing kind of a perturbation expansion here. The small changes of n lead to the Bragg scattering, but the condition for the maxima can be determined using the average value of n.



#3
Apr1314, 04:56 AM

P: 106

Oh okay because the crystal came with a designated n and the Bragg equation seemed useless then because this would vary. Unlike normal Bragg diffraction though we change the frequency of the sound wave causes a change in the angle does this sound right?



#4
Apr1314, 04:57 AM

P: 106

Bragg and Brillouin diffraction
Sorry worded poorly. A Bragg angle is a defined angle for constructive interference of the incoming and outgoing wave. But in this case I'm guessing we can change the Bragg angle by varying the frequency of the sound wave is this correct?



#5
Apr1314, 12:09 PM

Sci Advisor
P: 3,593

Yes, because changing the frequency of the sound wave you change also the wavelength of the sound which modulates the diffractive index and acts as a lattice for Bragg scattering.



#6
Apr1314, 12:11 PM

P: 106

Sweet but for brag diffraction the theta in must equal the theta out. Seeing as you can keep the theta in constant and change the theta out I'm assuming it's fundamentally different?



#7
Apr1314, 12:42 PM

Sci Advisor
P: 3,593




#8
Apr1314, 12:45 PM

P: 106

Well that's what I was taught. It's what my textbook introduction to optical electronics and this website says, so now I'm just doubley confused.
http://hyperphysics.phyastr.gsu.edu/hbase/quantum/bragg.html 


#9
Apr1414, 01:28 AM

Sci Advisor
P: 3,593

I don't know what your book is saying, but this website is simply explaining Bragg scattering. However I don't see why this should be related to your setup.
See, http://en.wikipedia.org/wiki/Diffraction_grating 


#10
Apr1414, 02:49 AM

P: 106

Never mind had a chat to a solid state lecturer. Well Bragg's law tells you the angle at which theta is the incident and reflected angle producing constructive interference. Changing the lattice structure will require you to change the angle to get a new Bragg angle. This is different from my setup because with my set up we had a constant incident angle and altered the frequency of the waves to alter the outgoing angle. Which obviously wasn't equal to the incident angle like Bragg's law stare, yet when we used the equation we had to define theta as the outgoing angle only.



Register to reply 
Related Discussions  
Xray Diffraction and Bragg's Law  Advanced Physics Homework  0  
Bragg Diffraction Help  Introductory Physics Homework  1  
Bragg Diffraction  Physics Learning Materials  0  
Bragg diffraction  Advanced Physics Homework  5  
Bragg's Diffraction  Introductory Physics Homework  0 