Create Laser-Like Light Beam: Is It Possible?

In summary: Thanks Claude. :)In summary, you could potentially create a focusing system that would allow a beam of light to be outputted for a distance of miles. However, the beam would be less focused and less powerful the further away it was from the focal point.
  • #1
Jake
90
0
I was wondering somewhat randomly, and pointlessly about the nature of light beams and how ordinary light sources emit beams in all directions in a very un-concentrated manner. And of course lasers emit a beam that almost totally focused on a single point. So I was wondering, would it be possible to say, place a lightbulb inside a system of mirrors that redirected and refined the light to a single point that would be usefull for long-range transmissions? Say several miles. In other words could you make a system of mirrors that could re-focus all random beams of light into a single, laser-like powerfull beam.

Thanks for the help! :)
 
Science news on Phys.org
  • #2
Laser beams have several qualities that differentiate them from other light sources.

- They are highly directional (Power flow is confined to a small angular range).
- They are coherent (All the photons are 'in step' with one another).
- They are monochromatic (Mostly, there are some lasers that operate over a broad spectrum, so called supercontinuum lasers).

A light source must have all these properties to imitate a laser beam in terms of power output.

Even if you had a perfect point source and had an elliptical cavity to focus the light, there is no way to guarantee all the photons will be 'in-step' for two reasons. One, incoherent sources typically emit over a broad range of wavelengths, different wavelengths quickly move out of step as they propagate. Two, the mechanism by which this radiation is emitted does not guarantee that the photons will be in phase at the point of emission.

So, in summary, no, it is not possible to turn an incoherent source into a coherent source using mirrors.

Claude.
 
  • #3
Thanks Claude.

Ok so it couldn't imitate a laser. But it could refocuse the light to a single, very powerfull point. My main question is, and I should have state this more clearly, how long (distance) could these photons hold that "focus". Naturally, over distance the photons would spread out, but by how much? Is it possible that it could retain most of its focus over perhaps miles?

Thanks again :)
 
  • #4
does the word collimation says anything to you?

Best Regards,

DaTario
 
  • #5
Jake said:
Thanks Claude.

Ok so it couldn't imitate a laser. But it could refocuse the light to a single, very powerfull point. My main question is, and I should have state this more clearly, how long (distance) could these photons hold that "focus". Naturally, over distance the photons would spread out, but by how much? Is it possible that it could retain most of its focus over perhaps miles?

Thanks again :)

There are several physical limits that apply.

The major one is probably this: with imaging optics, you cannot increase the source brightness (the power density per unit solid angle).

There are also some diffraction limits, but if you have large lenses they won't matter to your problem.

You could certainly build a lens to focus your light over a distance of miles. I don't recall offhand how you calculate the spot size from the geometry, though. Google finds:

http://www.edmundoptics.com/techSupport/DisplayArticle.cfm?articleid=268 [Broken]

which should probably tell you more than you want to know :-)
 
Last edited by a moderator:
  • #6
A parabolic mirror on a spotlight does what you are describing.
 
  • #7
This is going to sound stupid: what do you mean when you say a laser has power?

~Kitty
 
  • #8
Jake, When focusing anything, you basically have a trade off between resolution and depth of field (how long it holds focus, otherwise known as the Rayleigh range of the beam). The shorter the focal length of your objective, the smaller the focus will be, however the Rayleigh Range will also be reduced. Longer focal lengths will not be able to focus the beam down as far, however the light will be focused over a much longer length (not miles, you are probably looking at distances more like cm, or at the very most a metre or so).

Kitty, Power is a quantity with units of Watts, or Joules per second. When we say a laser has a power of 10 W, we mean that it is outputting 10 Joules of energy per second. Lots of lasers however are not continuous wave (CW), but pulsed, so one must differentiate between averaged power and peak power. A femtosecond pulse Ti:Sapphire laser may have average powers of milliwats, but peak powers can easily go into the Gigawatts (billions of watts) thus making them much more dangerous than a CW laser with the same average power.

Claude.
 

1. Can a laser-like light beam be created without using a laser?

Yes, it is possible to create a laser-like light beam without using a traditional laser. This can be achieved through a process called optical trapping, which uses focused beams of light to manipulate small particles or molecules. However, this method does not produce a coherent beam of light like a laser does.

2. What are the key components needed to create a laser-like light beam?

The key components needed to create a laser-like light beam are a source of light, a medium to amplify the light, and a resonator to reflect and focus the light. These components work together to produce a coherent and intense beam of light.

3. Is it possible to create a laser-like light beam in any color?

Yes, it is possible to create a laser-like light beam in almost any color. The color of the light beam is determined by the type of medium used to amplify the light. Different materials produce different wavelengths of light, resulting in a variety of colors.

4. How does a laser-like light beam differ from a traditional laser?

A laser-like light beam and a traditional laser differ in several ways. A laser produces a coherent beam of light with a single wavelength, while a laser-like light beam is not as focused and can have multiple wavelengths. Additionally, a laser-like light beam does not require the use of a laser cavity or mirrors to produce the light.

5. What are the potential applications of a laser-like light beam?

A laser-like light beam has many potential applications, including optical trapping for scientific research, laser cutting and welding in manufacturing, and laser therapy in medical treatments. It can also be used in telecommunications, spectroscopy, and entertainment, among others.

Similar threads

  • Optics
Replies
14
Views
1K
  • Optics
Replies
3
Views
645
Replies
25
Views
3K
Replies
26
Views
4K
Replies
10
Views
2K
Replies
5
Views
1K
Replies
14
Views
2K
Replies
7
Views
1K
Replies
8
Views
2K
Back
Top