12 DC Volt Boost to 15 DC Volt - 1 amp

AI Thread Summary
The discussion revolves around boosting a 12VDC power supply to 15VDC to power Labtech speakers in an RV setup. Users suggest trying the speakers at 12V first, as many devices can operate on slightly lower or higher voltages without issues. Concerns are raised about the safety of adding rechargeable AA batteries to achieve the desired voltage, with warnings about potential risks like smoke or flames. Recommendations include using an isolated DC-DC converter for a safer voltage boost solution. Overall, testing the speakers at 12V is encouraged before making modifications.
RV-Traveler
Messages
1
Reaction score
0
Superb Old Labtech Speakers to add to my RV without 120 Volt AC
The Labtech AC adapter's output is 15VDC 1000ma.
Using my existing 12VDC power supply (2 - 6VDC inline Deep charge Batteries)
may I boost this output to 15VDC by adding 2 ?or? 3 Duracell Rechargeable AA batteries.
Duracell posts these NiMH AA as 1.2V / 2450mAh.
These AA would be all inline and on the + line of the RV power.
Any possible problems I overlooked?
How do we estimate how long the AA will last or do we how do we know when the AA batteries need replacement?
N.B.: All batteries will be charged while driving with the 1000W Powerbright Inverter in my 2500D Silverado.
 
Engineering news on Phys.org
I would highly suggest not doing that. You might be adding smoke and flames along with your speakers.

Try the speakers at 12V and see how that works.

BoB
 
I would actually be surprised if it didn't run fine off of 12V. Many devices like this will operate on voltages that are slightly higher or lower than they're rated V. You may lose a little volume at max level, but I doubt it will be much. I am running a device that's supposed to take 5VDC and I'm running it from 12VDC. I don't recommend this, but it was a cheap enough device I figured I'd give it a shot.

I also have run a device rated at 12V on a 9V power supply without a problem. I would go ahead and give it a try, just make sure you get the polarity correct, I have seen devices get killed when the polarity is reversed...
 
For a one-off, I'd just get an Isolated DC-DC converter if this is a concern.

You could then take your 12V input to 15V safely and in a nice little package.
Something like this might work http://products.cui.com/CUI_PTK15-Q24-S15_Datasheet.pdf?fileID=1081
 
Last edited by a moderator:
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
Thread 'Beauty of old electrical and measuring things, etc.'
Even as a kid, I saw beauty in old devices. That made me want to understand how they worked. I had lots of old things that I keep and now reviving. Old things need to work to see the beauty. Here's what I've done so far. Two views of the gadgets shelves and my small work space: Here's a close up look at the meters, gauges and other measuring things: This is what I think of as surface-mount electrical components and wiring. The components are very old and shows how...
Back
Top