Register to reply

What is the reason for grounding a circuit ?

Share this thread:
shalikadm
#1
May4-12, 01:37 AM
P: 63
I have seen that in some circuits there's grounding...I know that earthing is for keep a part of a circuit in a zero potential...Don't know why it's done...Here's some circuit's..Tell me why it's been earthed..
Phys.Org News Partner Physics news on Phys.org
A new, tunable device for spintronics
Watching the structure of glass under pressure
New imaging technique shows how cocaine shuts down blood flow in mouse brains
gneill
#2
May5-12, 02:06 PM
Mentor
P: 11,683
Grounds on circuit diagrams can be there for practical reasons or for convenience, or both.

Note that not all circuit grounds are actual Earth connections -- that is, not all grounds have a physical connection to the Earth. They may connect to a metal chassis (or circuit container) or just represent one of the common power supply rails (usually the 0V supply reference point, particularly for circuits with multiple supply voltages such as +/- 15V, or 12V and 5V, and so on).

When used for convenience they represent a common reference point from which circuit potentials can be measured, and are treated as though wires were drawn connecting them all together. This serves to unclutter diagrams, especially where if the wires were actually drawn in they would cross over other wires and make the drawing harder to understand.

The practical reasons include shielding (from stray electromagnetic noise), polarity recognition for interconnecting circuits, and safety features. Actual Earth connections are important for safety reasons so that equipment potentials don't 'float' far from Earth potential and create shock hazards when people come in contact with the chassis or controls; This is true particularly when AC mains voltages are involved. Actual Earth connections can also be important for high performance antenna systems, where a 'pool' of charges at constant potential (Earth ground potential) is helpful for allowing maximum current flow in the antenna circuit in response to induced signal voltages.

Circuit grounding is actually a pretty complex subject, and in some cases is more of an art than a science particularly in sensitive circuits where noise suppression and avoidance of exotic feedback paths is necessary. Google "ground loop" or "phantom loop" for a taste of the topic.
Drakkith
#3
May5-12, 08:29 PM
Mentor
Drakkith's Avatar
P: 11,873
Our building at work has a "single point grounding system" for all of the test equipment. This enables all of the different pieces of testing equipment, which aren't all connected directly to each other, to use the same reference point for measuring voltage values and serves as a safety mechanism in case of electrical equipment faults. Without this, different grounds could have different potentials and cause testing failures.

shalikadm
#4
May5-12, 09:02 PM
P: 63
What is the reason for grounding a circuit ?

The first diagram shows a circuit that is used to measure current across the diode against voltage and to draw V-I characteristic diagram for a diode..when the current flows to the left direction the diode is forward biased and when the current flows to right direction the it's reverse biased...But I wonder what the reason is for grounding between the two batteries having opposite terminals connected...explain this for me..
Drakkith
#5
May5-12, 09:09 PM
Mentor
Drakkith's Avatar
P: 11,873
Quote Quote by shalikadm View Post
The first diagram shows a circuit that is used to measure current across the diode against voltage and to draw V-I characteristic diagram for a diode..when the current flows to the left direction the diode is forward biased and when the current flows to right direction the it's reverse biased...But I wonder what the reason is for grounding between the two batteries having opposite terminals connected...explain this for me..
There may not be any reason other than that was simply how the diagram was designed. If these are practice circuits then they don't need to be real items.
shalikadm
#6
May5-12, 09:15 PM
P: 63
Quote Quote by Drakkith View Post
There may not be any reason other than that was simply how the diagram was designed. If these are practice circuits then they don't need to be real items.
So can we use that circuit to draw the V-I graph without that grounding between the the two cells ?
Drakkith
#7
May5-12, 09:17 PM
Mentor
Drakkith's Avatar
P: 11,873
Quote Quote by shalikadm View Post
So can we use that circuit to draw the V-I graph without that grounding between the the two cells ?
If you aren't involving the ground at all, then I don't see why not.
shalikadm
#8
May5-12, 09:28 PM
P: 63
In our coursework it mention,that we must undergo 3 procedures before using transistors..

1.forward bias EB junction with low voltage
2.reverse bias BC junction with high voltage
3.ground points where it should be kept in a zero potential.

I don't understand the 3rd step..what are the points that should undergo a zero potential and why ?


Register to reply

Related Discussions
Newb question about circuit grounding Electrical Engineering 11
Grounding/earthing in a simple circuit General Physics 3
Grounding the output of the circuit Electrical Engineering 2
Grounding a DC Circuit Engineering, Comp Sci, & Technology Homework 9
Grounding a circuit Introductory Physics Homework 1