# How to build a simple AC motor with Styrofoam

by alexia-m
Tags: ac current, ac motor, magnet, project, rotating
 P: 1 Hello everyone, For my physics class, I want to build an AC motor with styrofoam, magnets, screws and magnet wire. So far, I have built a cylinder of about 2.5" of radius and 1" in height with eight magnets (strengh 6/10) around it. Each magnet is glued on the side of the cylinder alternatively north, south, north, ... . This cylinder is crossed by a wooden stick that allows it to rotate. I also built a ring of styrofoam that goes around the cylinder. Across each magnet on the outer ring, I have eight screws with wire magnet wrapped around them (150 turns each). Should I wrap the bolts alternatively counterclockwise and clockwise or does that matter? Also, I heard that I need to have AC current going through it (I have tried with a 9V battery in the past which didn't make the system rotate). How can I get an AC current going through it? I also tried to light a small LED light by connecting the magnet wires around one bolt to the led light and forcing the center wheel to turn. The light did NOT turn on. How can I make it light up? If I connect all the coils in series, would that work? My teacher said that there was a way to make a commutator with aluminum wrapped around a stick and cut on one side. How would that work? Please, let me know if you have any idea to make this project work. I would greatly appreciate it! Thank you. Alexia-m Attached Thumbnails
Homework
HW Helper
Thanks
P: 12,901
 How can I get an AC current going through it?
Hook it up to an AC voltage source?
 My teacher said that there was a way to make a commutator with aluminum wrapped around a stick and cut on one side. How would that work?
It would allow you to apply current for only half a turn.
The principle is the same as: http://www.electronicsinfoline.com/P...ic_motor.shtml
... only, there, the insulation has been filed off half the circumference of the wire.
Mentor
P: 11,779
 Quote by alexia-m My teacher said that there was a way to make a commutator with aluminum wrapped around a stick and cut on one side. How would that work?
Did you try a Google search on something like "motor commutator"?

 PF Gold P: 954 How to build a simple AC motor with Styrofoam "Should I wrap the bolts alternatively counterclockwise and clockwise or does that matter?" Yes you should, since your magnets are arranged with alternating polarities. It does matter. "Also, I heard that I need to have AC current going through it" You heard correctly. If you use d.c. the rotor will just lock in one place. With a.c., once you've spun the rotor up to a fast enough speed by hand, it should continue to rotate as a 'synchronous motor'. Its rotation frequency will be a submultiple (depending on the number of poles) of the a.c. frequency. "My teacher said that there was a way to make a commutator with aluminum wrapped around a stick and cut on one side. How would that work?" It wouldn't work for your motor, because the rotor has the permanent magnets and the coils are in the 'stator' (stationary bit).
Homework
HW Helper
Thanks
P: 12,901
 It wouldn't work for your motor, because the rotor has the permanent magnets and the coils are in the 'stator' (stationary bit).
The axle is an insulator right?

Put foil around half the circumference of part of the axle, use two brushes ... one is wired to the power supply and the other to the coil. This will break the circuit for half the cycle.
 PF Gold P: 954 Simon. There are several coils spaced around the stator circumference.
 Homework Sci Advisor HW Helper Thanks P: 12,901 Four coils and eight magnets, equally spaced ... yes I saw. The magnets are alternating N-S, everything has nice tidy symmetry. The half-period on half off thing was just an example fo how to do timing, not recommended timing for this particular design. How to design the motor is OPs job, surely? The point: Positioning conducting strips around the axle can still time the current to the coils however you want (effectively phase-locks a square wave to the rotor) ... this motor will work using a commutator and you don't have to crank it up first.
 PF Gold P: 954 "How to design the motor is OPs job, surely?" Yes indeed.
 PF Gold P: 954 Alexia-m: PLease report back on how you get on.
Homework