Cooling Time of Steel Block

by 1988ajk
Tags: block, cooling, steel, time
1988ajk is offline
Jan30-13, 11:50 AM
P: 23
I have a steel block (2.75m x 1.6m x 0.5m) sat at 1000C in ambient air (22C)

How long will it take for a surface to drop to say 800C

should i use the heat transfer eq: Q=KA[itex]\Delta[/itex]T to find the power in joules per second, then transpose to find seconds somehow???

Any help will be appreciated

Phys.Org News Partner Science news on
Lemurs match scent of a friend to sound of her voice
Repeated self-healing now possible in composite materials
'Heartbleed' fix may slow Web performance
TerryTate is offline
Jan31-13, 01:00 PM
P: 3
Hi Adam. Your block sitting in open air is undergoing convective heat transfer. For transient analysis of this type, you'll need to use the lumped capacitance approach. We ignore the temperature gradient inside the block and assume that the entire block is at the same temperature. Then, with an energy balance, we equate the rate of heat transfer out of the block (convection) to the rate of change in internal energy of the block.

[itex]-\dot{E}_{out} = \dot{E}_{st}[/itex]


[itex]-hA_{s}(T - T_{\infty}) = \rho Vc\dfrac{dT}{dt}[/itex]

With a bunch of exciting math, we can arrive at:

[itex]\dfrac{\rho Vc}{hA_{s}} \ln\dfrac{T - T_{\infty}}{T_{i} - T_{\infty}} = t[/itex]



\rho = \text{material density} \\
V = \text{volume} \\
c = \text{specific heat capacity} \\
h = \text{convective heat transfer coefficient} \\
A_{s} = \text{surface area exposed to the air} \\
T = \text{final temperature} \\
T_{i} = \text{initial temperature} \\
T_{\infty} = \text{temperature of the air} \\
t = \text{time taken to cool from } T_{i} \text{ to } T \text{ in seconds}\\


At this point, consult some references to determine the specific heat capacity and the convective heat transfer coefficient, and then it's plug and chug. Watch out for units!

According to my reference here:


c_{steel} = \text{440 } \dfrac{\text{J}}{\text{kg}\cdot{\text{K}}} \\
h_{air} = \text{20} \dfrac{\text{W}}{\text{m}^{2}\cdot{\text{K}}}



Keep in mind this is an approximation because we are assuming the gradient in the block has no effect on the rate of cooling (although most likely good enough for your needs). A measure of the validity of the approximation can be found through calculating the Biot number.


Bi = \dfrac{hL_{c}}{k}\\

\text{Where:} \\

L_{c} = \dfrac{V}{A_{s}} = \text{characteristic length} \\
k = \text{thermal conductivity of the material} \\


For a good approximation, Bi should be much less than 1.

Hope that helps!
LawrenceC is offline
Feb2-13, 09:10 AM
P: 1,195
You have a bit more of a problem here. The block is at 1000 C. Therefore radiation is the dominant heat transfer mode. Natural convection is dwarfed by radiation at these temperatures. My advice is to create a FE for FD model of it and include the radiation boundary condition along with the natural comvection condition.

If you cannot do this you can approximate the effect of radiation and lump it into the convection coefficient. It's crude but better than ignoring the major heat loss.

HowlerMonkey is offline
Feb12-13, 07:36 AM
P: 275

Cooling Time of Steel Block

If you got access to the ford automobile factory in detroit, you might be able to measure this in real life.

Last time I was there, I remember red hot ingots emerging from where they were made and them sitting (still red) before they were moved to where they would be worked.
pukb is offline
Feb13-13, 12:02 AM
P: 90
Assuming the block to be lumped, you can equate convection loss + radiation loss to heat term at steady state.
LawrenceC is offline
Feb13-13, 05:58 AM
P: 1,195
Due to its nonlinearity you'll have to perform a numerical integration in order to solve it. Newton Raphson embedded in a fully implicit scheme would work well.

Register to reply

Related Discussions
A block of cheese hits a steel wall... General Physics 10
How much work must you do to push a 13 block of steel across a steel table at a ste Introductory Physics Homework 11
2 Bullets, same mass, same v, fired at wood and steel block, which block has > v? Introductory Physics Homework 14
Steel Block Rotating On A Steel Table Introductory Physics Homework 1
Cooling iron and steel Atomic, Solid State, Comp. Physics 9