Recent content by Beeorz

Okay, that makes sense. Now if I was using signal levels a through e only: ~The range would be from 0 to 10 and have 4 zones. ~Thus 10/4 = 2.5 ~00 is 0-2.5 ~01 is 2.5-5 ~10 is 5-7.5 ~11 is 7.5-10 If that is all correct then the answer would indeed be A because: a=00 b=01...

Obtain the digital words corresponding to the indicated analog signal levels, a through j, as shown in Figure P8.38, that would be assigned by an A/D system with 2 bits. http://img256.imageshack.us/f/eehmrw1.png/ a. None of the above b. a=11, b=01,c=10,d=01, and e=01 c...

The PCI bus found in many computers transmits 64 bits per clock cycle at 33MHz. How does the bandwidth of the PCI bus compare to the serial FireWire (IEEE 1394) serial bus specification, which is 400 Mbits per second? a. The FireWire serial bus is better. b. The PCI bus is better. c. They...

My group is currently working on design generation and selection. We have a just about all of it done and ready to go but we are unsure what the professor means by baseline. Here is what he wrote about it: Baseline refers to a set of design variables or expectations that you judge/compare...

Not sure if I am using the right technique or even using the technique correctly... http://img8.imageshack.us/img8/6346/practiceprob.th.jpg http://img44.imageshack.us/img44/8479/workedpracticeprob.th.jpg

ty very much, now I just to put it all into practice

I've read through a ton of material and still do not quite understand it. The way that we were taught was: 1) Redraw, with load removed 2) Redraw, find Voc 3) Redraw, find Rth 4) Redraw, using TEC with removed load Most of my questions involve finding Voc and Rth. I understand the steps...

Bond Enthalpies..please help! Got the first one, but can't figure out how to do "b" and "c." Not understand which ones make/break. http://rapidshare.com/files/157266091/Enth.jpg

Louisiana State University (LSU) - Required course for mechanical engineers. The only "drawing" course we are required to take. I'm guessing they are wanting us to at least be able to understand engineering drawings even if we are not the one having to draw them.

Homework Statement You are given a 250mg tablet of Vitamin C, C6H8O6. How many atoms are in the Vitamin C sample? The Attempt at a Solution Formula Mass = 6(12.01)+8(1.01)+6(16.00) = 176.1 g/mol 250mg (1g/1000mg)(1mole/176.1g)(6.02e23molecules/1mole) = 8.546 molecules How do I...

Figured out #5 after hours of looking at it. Still need help with #2!

Hello everyone, I am having problems with these 2 drawings. Basically, I am suppose to draw the 3D (isometric) view of the diagrams. The diagrams both provide a front and right-side view but I cannot seem to picture the object and don't know where to start. Please help...

ah wrong section, ill post it up in the homework section..sorry!

1)Basically I am unsure if the top view is correct. The front and right side views are correct since they are given. http://img300.imageshack.us/my.php?image=bookprobsvf9.jpg 2)I am not sure if any of this is correct. Please help me out...

Homework Statement Find the volume of the solid obtained by rotating the region under the graph of y=1/x and y=1/x^2 about the vertical axis x=-1 Also given are points on the y-axis (0,2) and (0,5). I guessing these points are specific sections of the graphs where we find the volume...