Radio Power Conversion: Convert mV/m or nW/m2 to Watts

  • Thread starter Thread starter coltonk
  • Start date Start date
  • Tags Tags
    Power Radio
AI Thread Summary
The discussion centers on converting measurements from RFExplorer, which displays power in mV/m and nW/m2, into watts to assess antenna efficiency. It highlights that nW/m2 reflects power at a specific location but does not account for the antenna's radiation pattern, which affects readings based on directionality. Suggestions include using an SWR meter for more accurate power measurements and considering a test range with a far-field meter for comparative analysis. Mapping the radiation pattern with a rotator can further enhance understanding of antenna performance. Accurate computation of absolute efficiency is deemed important for optimizing antenna design.
coltonk
Messages
11
Reaction score
2
TL;DR Summary
Converting units of transmitted power
I have searched the internet and spoken to the manufacturer of my equipment and can not find an answer. I am using RFExplorer (test equipment) to measure the power generated by my ham radio antenna. The only options for displayed power is mV/m or nW/m2. I am trying to find out how to convert these into transmitted watts so I can see how efficient my antenna is radiating and my radio output is watts.
 
Engineering news on Phys.org
Can you just borrow an SWR meter instead? BTW, mV/m is the E-field strength.

1650991721426.png

https://www.wimo.com/en/cn-901hp-swr-meter

Is this your meter/spectrum analyzer?

1650988178300.png
 
Last edited:
nW/m2 is the best your meter can do with power measurements. It is the power measurement at the measurement location, a surface measured in m2. The problem is your meter doesn't know about how the antenna radiates in the other directions. With everything else being equal a more directive antenna will give you a higher reading on the beam axis, and lower readings off of the beam axis.

So, if you could measure in every direction, you could add up the total power. Really, you're integrating the measurements over a closed surface around the antenna. Alternatively, if you know the radiation pattern of your antenna, maybe you could use the meter to calibrate a theoretical summation over all directions.
 
berkeman said:
Can you just borrow an SWR meter instead? BTW, mV/m is the E-field strength.

View attachment 300618
https://www.wimo.com/en/cn-901hp-swr-meter

Is this your meter/spectrum analyzer?

View attachment 300616
That's what I have..
 
Is computation of absolute efficiency important?
Why not set up a test range with a far field meter, say beyond 60λ. Then you can make comparative measurements to improve the design relative to a simple dipole. If you have a rotator for your antenna under test you can also map the radiation pattern.
 
  • Like
Likes berkeman and DaveE
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top