Recent content by tesla93

But the sounds are going in different directions, my professor said you can't treat sounds like forces and take a resultant. He said that I had to use the directionality index but I don't know how to apply that. I used Lp = Lw - 20log(r) - 11 - Ae with the only unknown being Lw, solved for...

I recently performed a noise lab and I am required to write a program to find the room constant of the room where the data was collected. Basically I would be using the formula: Lp = Lw + 10log(Q/[4*pi*r^2] + 4/R) Where Lp is the sound pressure level which was collected during the...

The Problem: Bio fuels are receiving more and more attention. For biomass waste materials (cellulose, manure etc.), the first step in the process is typically to convert the biomass to sugar (glucose, C6H12O6). This first step is only able to produce 0.1 g glucose per g of biomass. The...

While I'm at it, I'm having trouble with another question like the one above, but this time it's a mechanical system. It's the jpeg below. I started off with the writing equations for each mass Mass 1: K1x1 + DB(x) + k2(x1-x2) = 0 Mass 2: m2D^2x = DB(x1-x2) + k2(x1-x2) First off...

Ohhhh okay that makes sense. Took a while to wrap my head around it but I got the right answer in the end. Thanks! :)

Hey all, I'm stuck on a dynamic systems question, it's attached as a jpeg I started off by writing nodal equations for each node: Node 1: 1/R1(ei-eA)=C1D(eA-eo)+1/R2(eA-eB) Node 2:1/R2(eA-eB)=C2D(eB) I know that I have to isolate for ei and eo but I'm really confused with...

Awesome, thanks! :)

So then...the slope of the linear portion of the curve?

Hey guys, I recently did a compression lab with different materials (wood and pvc pipe) and I have to plot the stress/strain curves given the data collected, as well as find yield strength (0.2% offset), ultimate compressive strength, and modulus of elasticity. I've already calculated...

Sorry I was going off of my professors notes for a different system and he used P. Would this be correct if I was looking at specifically at the node Ti? 0=-1/R1(Ti-T1)-1/R5(Ti-To)-Ci(Q(t)-Ti) What I understood from nodal analysis is that you start at one node and look at what's going in...

So I have to write out nodal equations for a system that I was given, and I started off by drawing out the flow diagram to see where everything was. I'm having trouble starting the nodal equations though. The attachment has 2 diagrams: figure 1 is the correct diagram that models the thermal...

Homework Statement Determine whether each of the following functions is a solution of Laplace’s equation uxx + uyy = 0. x^3 + 3xy^2 ux=3x^2 uxx=6x uy=6xy^2 uyy=6x 6x+6x=12x and is therefore not a solution Did I do that right? I'm just learning about this topic and it's...

Oh okay I understand that. Thanks! I think I've got the right answer now

Homework Statement lim x→∞ of ((x^3+2x-∏)^(1/3))-x Homework Equations L'Hopital's Rule: If it is an indeterminate form, take the derivative of the top and bottom until you do not get an indeterminate form anymore. The Attempt at a Solution lim x→∞ of ((x^3+2x-∏)^(1/3))-x...

The problem is: lim as x→- ∞ (-5x/x-2)=-5 And I have to find the best interval of solutions for N Relevant equations: if x>N then |(-5x/x-2)-(-5)|<ε My attempt: |(-5x/x-2) - (-5)|<ε |-10/x-2|<ε x-2< 10/ε as x→-∞ we can assume that x-2<0 x-2<10/ε x< (10/ε)+2...