Error: no plot because it would be empty, using mcnpx

Click For Summary

Discussion Overview

The discussion revolves around issues encountered while using MCNPX and Moritz for plotting dose and fluence in a simulation involving a water tank, nozzle, and slit blend. Participants seek assistance in resolving an error message indicating that no plot can be generated due to it being empty.

Discussion Character

  • Technical explanation
  • Debate/contested

Main Points Raised

  • One participant describes their setup involving a water tank, nozzle, and proton beam, and expresses difficulty in plotting dose and fluence due to an error message.
  • Another participant mentions a problem with running Moritz from a specific PC, indicating that the executable is visible in the task manager but the GUI does not open.
  • A third participant suggests starting a new thread for clarity and requests more detailed information about the issues being faced.

Areas of Agreement / Disagreement

Participants have not reached a consensus on the issues raised, and multiple competing views regarding the problems with Moritz and MCNPX remain unresolved.

Contextual Notes

There are limitations in the information provided, including a lack of detail about the specific configurations used in the simulation and the nature of the error encountered. The discussion also reflects a potential misunderstanding of thread etiquette in the forum.

hu94mcnpx
Messages
1
Reaction score
0
Hello everyone!

I would like to ask you if anyone can help me solving my Problem with mcnpx. I created a file with a watertank, a nozzle and a slit blend on the surface. I also inserted a protonbeam and would like to plot the dose and fluence for examplte with Moritz. But when I execute the file the error: "no plot because it would be empty" shows up. I hope anyone can help me. The file runs but I just have the Problem with plotting the dose and fluent.

Thank you!
 
Engineering news on Phys.org
Hello everyone!
Pb to run moritz from a given PC

thnks in advance for help
Thibaut
 
in fact exe in seen in the taskmanager but not GUI open..
 
Please start a new thread with your question, rather than adding your new question onto the end of a years-old thread. Please also give much more information in your new thread start, since your posts below make basically no sense as written. Thank you.

ThibautVincho said:
Hello everyone!
Pb to run moritz from a given PC

thnks in advance for help
Thibaut
ThibautVincho said:
in fact exe in seen in the taskmanager but not GUI open..
 

Similar threads

Mesh Tally in MCNPX for Dose Calculation / How to Add & Visualize?
  • · Replies 0 ·
Replies
0
Views
1K
MCNPX ver 2.7 error: ''bad problem in xact in routine tpefil chg_mem error''
  • · Replies 3 ·
Replies
3
Views
2K
MCNPX output proton energy is zero?
  • · Replies 8 ·
Replies
8
Views
1K
"No tally, no plot" error MCNP6
  • · Replies 24 ·
Replies
24
Views
6K
Silvaco: "simulator has unexpectedly exited with status -1073741819"
  • · Replies 2 ·
Replies
2
Views
4K
MATLAB Getting Error When Plotting Graph (Using Python w/ matplotlib.pyplot)
  • · Replies 5 ·
Replies
5
Views
3K
Mathematica Issues With Mathematica - AGAIN (Not Displaying Plots)
  • · Replies 5 ·
Replies
5
Views
3K
Proton transport problem using MCNP
  • · Replies 5 ·
Replies
5
Views
5K
Using Maxima to plot error in Fourier series
  • · Replies 1 ·
Replies
1
Views
2K
Experiment - how temperature changes along a tube, using heaters
  • · Replies 14 ·
Replies
14
Views
2K