Number of Teeth for Planetary Gear Train Question

AI Thread Summary
To determine the number of teeth for a ring gear in a planetary gear train with a sun gear and two planetary gears, the formula R = 2P + S is commonly referenced, where P is the number of teeth on the planetary gears and S is the number of teeth on the sun gear. However, the presence of an extra planetary gear complicates the application of this formula, suggesting that a custom derivation may be necessary for specific designs. The discussion highlights the iterative nature of gear design, emphasizing the importance of stress limits, lubrication, and vibrational analysis. A practical example shows that using 40 teeth for the sun gear and 18 for the planetary gears results in a ring gear with 80 teeth, confirming the use of the formula with adjustments. Ultimately, while the formula provides a starting point, each design may require unique considerations based on its specific parameters.
StephenD420
Messages
97
Reaction score
0
Hello all:

I have a quick question concerning a variation of a planetary gear train I am working on.
If I want a sun gear and then two planetary gears in between the sun and ring gear (like is shown in the attached picture), how do I find the number of teeth for the ring gear? Would the number of teeth still follow the formula R = 2P + S ?
Or would more gear teeth need to be added, and if so how many?

Example:
If the sun gear has say 94 teeth and the planetary gears have just 4 teeth would the ring gear have 102 teeth? or 104 teeth or some other number of teeth?

Thank you guys so much for the help.
Stephen
 

Attachments

  • GearPic.jpg
    GearPic.jpg
    5.7 KB · Views: 1,058
Engineering news on Phys.org
I've never seen a ring gear that was not round.
 
Any of the gears can have any number of teeth within the physical constraints of your application. I start with the desired gear ratio. Then I decide if I want to fix the ring or the planet carrier. Then I work backwards to see how many teeth I need, making sure that I remain within the stress limits of the material. Then I start looking at lubrication and cooling. Lastly, I check vibrational modes and fatigue. All such designs are iterative, and at any point in this process I may find a reason to stop and start another iteration. Pratt is just now selling their first geared turbofan engine after 15 years of iterations. That was a very difficult gear design and they seem to have finally succeeded after many have failed over the last 4 or 5 decades.
 
But I have read that the number of teeth in the ring gear has to equal R = 2P + S where P is the number of teeth in the planet gears and S is the number of teeth of the sun gear. Is this not true?

And yes the gears are circular just my drawing skills in paint leaves much to be desired.

Stephen
 
That may be true. I seem to remember something like that from my training many decades ago. It was derived from the basic geometric relations that enable the gears to mesh correctly. But your application is not the common one. You have an extra planet. So I would not use any standard derived formula unless I went thru the derivation again to make sure it applied to this specific case. But then by the time I did that, I could have the design substantially complete. That is what I meant when I said they could have any number within the physical constraints of your application.

I'll go back and check my notes to see what else might apply to your example.
 
Last edited:
Using the equations from http://blog.makezine.com/2010/06/28/make-your-own-gears/

I found that using 40 teeth for the sun gear, 18 teeth for the planet gears and 80 teeth for the ring gear gives the following outer diameter values in inches using a diametrical pitch of 8.835729338

sun gear: 4.753427634
planet gears: 2.263536968
ring gear: 9.280501571

so adding 2* outer diameter of P + outer diameter of S gives 9.280501571 which would be the outer diameter of the ring gear, thus adding the outer diameter of the sun gear and the two planet gears gives the outer diameter of the ring gear.
so I believe that this is correct, right?
So it seems you use 2P + S, where here P is the number of teeth of planetary gears and S is the number of teeth of the sun gear, and then add 4 to this to get the number of teeth for the ring gear. Does this sound right?

Thanks for the help.
Stephen
 
Last edited:
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Thread 'What type of toilet do I have?'
I was enrolled in an online plumbing course at Stratford University. My plumbing textbook lists four types of residential toilets: 1# upflush toilets 2# pressure assisted toilets 3# gravity-fed, rim jet toilets and 4# gravity-fed, siphon-jet toilets. I know my toilet is not an upflush toilet because my toilet is not below the sewage line, and my toilet does not have a grinder and a pump next to it to propel waste upwards. I am about 99% sure that my toilet is not a pressure assisted...
After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
Back
Top