Hey guys me solve these questions (Electrical(electronics) Engineering)

7 replies · 6K views · last reply
hot_sauce
Messages
24
Reaction score
0
Hey guys please help me solve these questions !(Electrical(electronics) Engineering)

ok guys, I was on a vacation, and when I came back the professor just handed out an assignment, and I have no clue about it !

Please please, I really need your help on this. The assignment is due on the 28th ! Please I beg you to solve this for me !

I came back late, so I only have 2 days for it, as the rest of the class had the whole week ! pleaseeeeeeeeee i really need your help!these are the questions :
Q1) Find the equivalent resistance at terminals A-B in the circuit.

Circuit schematic with terminals A and B: a 6 kilo ohms resistor in series from A, a junction feeding a 3kilo ohms resistor and an 18kilo ohms resistor, a 6kil0 ohms resistor on the right, then a 10 kilo ohms resistor down to B; labelled RAB.
------------------------------------------------------------------------

Q2) Find the voltage across and charge on each capacitor for the network below :

Circuit schematic with a 120 V source on the left, a capacitor C1 in the top branch, a 4 uF capacitor C2 in a middle branch and a 2 uF capacitor C2 in a right branch.


----------------------------------------------------------------------------

Q3) State and prove the law :-

e=Ndφ/dt
--------------------------------------------------------------------------------Q4) Find Vo in the network :

Circuit schematic with a 4mA current source at the top, a 2mA current source on the left, a 2 kilo ohm and a 1 kilo ohm resistor, a 4V voltage source, a 4 kilo ohm resistor on the right, and the output voltage labelled Vo.


-------------------------------------------------------------------------------

Q5) A factory has a 240-V supply from which the following loads are taken :

Lightning: Three hundred 150kW, four hundred 100W, and five hundred 60W lamps.

Heating : 100kW
Motors : A total of 44.76kW with an average efficiency of 75%

Misc. : Various loads taking a current of 40AAssuming that the lightning load is on for a period of 4 hours a day, the heating for 10 hours a day, and the remaining for 2 hours a day.

Calculate the weekly consumption of the factory in Kwh when working on a 5 day week.

---------------------------------------------------------------------------
Q6) Use Mesh equations to find the current through 10 Ohm resistors.


Circuit schematic with a 15 V source on the left feeding a network of resistors labelled 10 Ohm, 8 Ohm, 5 Ohm, 3Ohm and 2Ohm.
 
Come on, try and make an attempt.

Q1. Use the formulas for getting the total resistance of resistors in series and resistors in parallel separately.
Q2. Learn how to calculate total capacitance of capacitors in parallel
Q3. Read up on electromagnetic induction
Q4. Same principles as question 1.
Q5. Read up on Ohm's law and Coulomb's Law.
Q6. Read up on mesh analysis.

You have enough time to learn this in two days trust me.
 
Last edited:
Ed Aboud said:
Come on, try and make an attempt.

Q1. Use the formulas for getting the total resistance of resistors in series and resistors in parallel separately.
Q2. Learn how to calculate total capacitance of capacitors in parallel
Q3. Read up on electromagnetic induction
Q4. Same principles as question 1.
Q5. Read up on Ohm's law and Coulomb's Law.
Q6. Read up on mesh analysis.

You have enough time to learn this in two days trust me.

well I have solved Q no.1 and Q no.4, but I am STRUGGLING with the rest, pleaaase help :(
 
hot_sauce said:
well I have solved Q no.1 and Q no.4, but I am STRUGGLING with the rest, pleaaase help :(

Please read the forum rules: you need to show some work before we can help you with homework questions.
 
Qno.1)
the 3 kOhm + 6 kOhm = 9 kOhm, which is in parallel with the 18 kOhm resistor. 1/R = 1/18 + 1/9. R = 6 kOhm. So, overall, that part has 6 kOhms in resistance. adding the other two resistors that are in series, 6 + 6 + 10 = 22 kOhm. the equivalent resistance is 22 kOhms.Also Q no,3 I got help from wikipedia and I've got that done now.

So I onlyneed help with Q no.2,5 and 6.
 
trust me bro, I would have solved the other ones if I could but I cant. Its not that I am not investing time into studying and solving them myself, its that I don't have anymore time !

The Mesh equation question is totally out of knowledge, since he taught that while I was gona and gave this assignment.

I really need the marks on this assignment, since I've been a little off in this course.

I really need help please.
 
Read through your notes or textbook on mesh analysis first.

If you want to read something online, try this:
http://www.allaboutcircuits.com/vol_1/chpt_10/3.html
http://mysite.wanadoo-members.co.uk/phil_robinson/mesh.html
 
Last edited by a moderator:
thanks for the help guys, I solved all of them, but I am not sure if I got Q no.5 right