Understanding Oscillator Circuits: Effects of Adding a Second Coil at 90 Degrees

  • Thread starter Thread starter Jdo300
  • Start date Start date
  • Tags Tags
    Angles Coils
AI Thread Summary
Adding a second coil at 90 degrees to an inductor in an oscillator circuit can affect induction and resonance. The second coil may not experience induction in the same way as a parallel coil due to the perpendicular orientation, which prevents effective flux coupling. If the second coil is positioned closer to the center of the first coil and tilted, some coupling may occur, potentially altering the circuit's behavior. The original experiment with a small coil around a lamp cord likely involved capacitive coupling rather than magnetic induction. Understanding these interactions is crucial for predicting changes in resonant frequency and circuit performance.
Jdo300
Messages
548
Reaction score
5
Hello everyone,

In my continuing pursuit of understanding of oscillator circuits, I came up with this question and was wondering if anyone here could give me some insight on this. I drew a picture to help me explain the idea but I would like to know what would happen if you have an inductor (air core solenoid for example) and you wrap a second coil around the first coil at 90 degrees to it. If the solenoid coil has an AC sine wave signal put through it, would the second coil experience induction in the same way as normal? If this solenoid coil were part of an oscillator, how would the presence of this second coil effect its operation (Particularly if a load is placed on it)? Would it change the resonant frequency of the oscillator circuit or simply dampen it?? I heard of someone who did a similar experiment and they say the second inductor produces pulsed DC... not sure though. Any help would be appreciated :-).

Thanks,
Jason O
 

Attachments

  • Coils.jpg
    Coils.jpg
    32.4 KB · Views: 556
Engineering news on Phys.org
Ohh one other note, the original experimenter who got the pulsed DC did not use coils at right angles, he took some small gauge wire and wrapped it around a lamp cord. He then ran a sine wave through the small coil and registered pulsed DC coming out of the lamp cord.
 
No, there would not be any flux coupling if the windings were done carefully. However, if the 2nd coil were pushed in a bit toward the center of the big coil (in your 2nd sketch), and the windings were tilted a bit, then I think you could get some net flux coupling. I don't know what your friend with the lamp cord was seeing, but it almost certainly wasn't from magnetic coupling. Lamp cord has both conductors in it, so wrapping a coil around both will not induce anything differential. He maybe got some capacitive coupling, or had an instrumentation problem.
 
If the coils are parallel, engineers always like to say they are talking to each other.


If they are perpendicular, then the fluxes can't link together.
 
Hmmmm interesting. Thanks for the information :-).
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Thread 'Electromagnet magnetic field issue'
Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...
Back
Top