AS-Interface control cabinet module

AI Thread Summary
The AS-Interface control cabinet module is a discrete I/O device that operates on the AS-I bus, featuring four PNP inputs and four relay outputs. Its primary function is to drive power circuits, typically managed by a host PLC that supports the AS-I bus. Users unfamiliar with this technology may find it challenging to understand its application from the datasheet. The discussion highlights the need for clarity on how this module integrates into control systems. Overall, it serves as a crucial component for controlling various devices in automation setups.
Ivan001
Messages
19
Reaction score
0
Engineering news on Phys.org
I have never seen one of these in my life but it makes sense to me that a general control component may need to drive power circuits and that is still often achieved with a relay.
 
It appears to be a discrete I/O module operating on AS-I bus that has 4 PNP inputs and 4 relay outputs. Presumably a host PLC or similar that supports AS-I bus can address the I/O.
 
  • Like
Likes trurle, Asymptotic and sophiecentaur
@Ivan001 what are you planning to use this information for? Will you be building something?
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Space vector modulation, motor control, implementation question
Replies
2
Views
1K
I want a temperature controller for a 12V, 40W ceramic cartridge heater
Replies
14
Views
5K
Help with waveform control: frequency, phase and amplitude
Replies
46
Views
5K
What is the "observer" in PID control?
Replies
12
Views
3K
Anyone familiar with SFP Fiber Optic Modules?
Replies
4
Views
2K
How to find a right RF module for a project?
Replies
6
Views
2K
Can I Use AC to Power DC LED Light Bars for Stage Production?
Replies
13
Views
4K
How can I reroute multiple signals from a 4 pin connector using a relay switch?
Replies
37
Views
6K
What Should Be the Overload Relay Values in a Star-Delta Diagram?
Replies
7
Views
8K
Amplitude modulation of signals with [suppressed] carrier
Replies
3
Views
3K

Hot Threads

Recent Insights

Back
Top