Cannonball - time required to stop its horizontal motion

In summary, the conversation discusses the computation of the time after which the horizontal velocity of a cannonball fired from a platform high above the ground would be zero. The conversation also mentions the use of equations to calculate the force of air resistance and the assumption that the force is constant. The speakers also discuss the need for a differential equation to account for the changing velocity of the object over time. They also mention the importance of having a basic understanding of physics and mathematics to fully understand the equations. The conversation ends with a discussion of the equations and their corresponding graphs, with the conclusion that the original equation used may not be accurate due to incorrect assumptions and that the drag coefficient for artillery shells may be smaller than that of a sphere.
  • #1
ChessEnthusiast
115
3
Let's imagine that we fire a cannon located on a platform high above the ground and we want to compute the time after which the horizontal velocity of the cannonball will be zero. Let's assume that we shoot at 0 degree angle.

1. Air resistance force
[tex]F = C_d \frac{\rho v^2}{2}S[/tex]

2. Assuming that the force from point 1 is constant (terrible assumption but I hope it does not affect the answer too much) we have
[tex]F = \frac{mv}{t}[/tex]
[tex]C_d \rho v^2 \pi R^2=\frac{mv}{t}[/tex] assuming [tex]S=2\pi R^2[/tex]
[tex]t = \frac{m}{C_d \rho v \pi R^2}[/tex]

Now, let's make up some rational parameters
initial speed: 800 m/s
drag coefficient: 0.47
mass of the cannonball: 300 kg
Radius: 0.5 m
air density: 1.2 kg / m^3

Now, as I plug in my data to the equation, I get the answer - roughly 0.8 s. I know that this answer is not rational. My question is, is this significant error caused by the assumption that the force is constant?
 
Last edited:
Physics news on Phys.org
  • #2
ChessEnthusiast said:
Now, as I plug in my data to the equation, I get the answer - roughly 0.8 s. I know that this answer is not rational. My question is, is this significant error caused by the assumption that the force is constant?

That's a good bet. You need a differential equation since the force of air resistance depends on the velocity of the object, which is changing over time.
 
  • Like
Likes ChessEnthusiast
  • #3
Drakkith said:
That's a good bet. You need a differential equation since the force of air resistance depends on the velocity of the object, which is changing over time.

Could you help me to write this equation? I've never done that before. Physics is not part of my college course, I'm simply an enthusiast.
 
  • #4
ChessEnthusiast said:
Could you help me to write this equation? I've never done that before. Physics is not part of my college course, I'm simply an enthusiast.

Not tonight, I'm getting ready for bed. I might be able to help you tomorrow though.
 
  • #5
ChessEnthusiast said:
Could you help me to write this equation? I've never done that before. Physics is not part of my college course, I'm simply an enthusiast.
I seriously think that, if you want the equation to be at all meaningful to you, you need to have some basic knowledge of the Maths involved. It is not much use diving into a subject like this without working upwards from scratch. Yes, you can get a 'feel' for many of these things in Physics but that's as far as you can hope to go without the Maths.
 
  • #6
ChessEnthusiast said:
we want to compute the time after which the horizontal velocity of the cannonball will be zero.
It seems the velocity will be of the form
$$v(t)=\frac{v_{0}}{1+t/t_{0}}$$
where ##t_{0}## is probably something like the ##t## you found. In any case, its horizontal motion will never stop.
 
  • #7
Well, I come up with two possible equations.

1. Assuming the force scales with the square of the velocity: ##V(t)=(0.0014758t+0.00125)^{-1}##

2. Assuming the force scales proportionally with velocity (##v## instead of ##v^2##): ##V(t)=800e^{-0.0014758t}##

Looking at the graphs of both equations, equation 2 looks to be a bit more realistic. Equation 1 results in the cannonball losing more than half of its velocity in one second, whereas equation 2 takes 527 seconds to drop to the same velocity. That 2nd equation is probably off by a significant amount, but equation 1 is entirely wrong for some reason. Not sure if I've solved my differential equation incorrectly or if we've used the wrong initial equations.
 
  • #8
Drakkith said:
Well, I come up with two possible equations.
1. Assuming the force scales with the square of the velocity: ##V(t)=(0.0014758t+0.00125)^{-1}##
Equation 1 results in the cannonball losing more than half of its velocity in one second
Sounds OK to me. Even if by "radius" OP means "diameter" the ball is still pretty light. BTW should not the area be ##\pi R^2## rather than ##2\pi R^2##?
 
  • Like
Likes ChessEnthusiast
  • #9
SlowThinker said:
Sounds OK to me. Even if by "radius" OP means "diameter" the ball is still pretty light. BTW should not the area be ##\pi R^2## rather than ##2\pi R^2##?

Taking 0.5 meters to be the diameter instead of the radius makes the equation seem much more realistic. A cannonball with a radius of 0.5 meters and a mass of 300kg has a density of 577 kg/m3. But if the diameter is 0.5 meters the density increases to 4,615 kg/m3, almost 9 times as much. The new equation becomes: ##V(t)=(0.000184t+0.00125)^{-1}##

The largest naval artillery ever fielded by the U.S. was the 16"/50 caliber Mark 7 guns on the Iowa-class battleships. These guns fired shells 16 inches in diameter (0.406 meters) with a mass of up to 1,225 kg at 820 m/s. With a diameter of 0.406 m and a length of 1.829 m the density of these shells was approximately 5,000 kg/m3. However, the mass vs cross-sectional-area of these shells was much higher, 9400kg/m2 vs 1500kg/m2 for the cannonball of diameter 0.5 m.

The equation for this shell: ##V(t)=(2.67*10^{-5}t+0.00122)^{-1}##

Graphing these equations shows that it takes 8 seconds for the cannonball to lose half its velocity compared to 0.847 seconds for the original equation.
However, the shell takes 45 seconds to lose half of its velocity and 136 seconds to reach a quarter, which seem like very reasonable numbers considering that they had a maximum flight time of about 90 seconds when fired at maximum range.
 
Last edited:
  • Like
Likes ChessEnthusiast
  • #10
Drakkith said:
However, the shell takes 45 seconds to lose half of its velocity and 136 seconds to reach a quarter
What is the source of these numbers, your equation or actual measurement? Don't forget that artillery shells are not balls. Their drag coefficient is probably much smaller than that of a sphere.
BTW,
Drakkith said:
A cannonball with a radius of 0.5 meters and a mass of 300kg has a density of 577 kg/m3. But if the diameter is 0.5 meters the density increases to 4,615 kg/m3, almost 9 times as much.
o:)
 
  • Like
Likes ChessEnthusiast
  • #11
Oh, @ChessEnthusiast, here's your equation with just the variables: ##V=(\frac{C_dρS}{2m}t+c)^{-1}##
To find little ##c##, set ##V## to the initial velocity, ##t## to zero, and then solve for ##c##. So ##V_0=\frac{1}{c}##
Then just plug in your value for ##c## into the equation.

SlowThinker said:
What is the source of these numbers, your equation or actual measurement? Don't forget that artillery shells are not balls. Their drag coefficient is probably much smaller than that of a sphere.

I used the drag coefficient for a half-sphere, which is 0.42. I looked again before making this post, but had a difficult time quickly finding a drag coefficient for an artillery shell. The best I could do was use the ~0.23 value from section 2.4 of this article. That certainly reduces the drag on the projectile by a good amount.
The rest of the values I found on wikipedia or a few sites on naval guns. I calculated the approximate density myself using these values.
 
  • Like
Likes ChessEnthusiast
  • #12
Using a drag coefficient of 0.23 as per my link in the previous post, along with a projectile velocity of 762 m/s, the new equation is: ##V(t)=(0.0000146x+\frac{1}{762})^{-1}##

Looking at some information on this naval weapons website, the striking velocity of a shell launched at a target at 10,000 yards is 632 m/s and the flight time is 13.2 seconds (look under the "Range" and "Armor Piercing with AP Mark 8" sections). Using our equation, the predicted velocity after 13.2 seconds of flight is 664 m/s. That's within 5% of the real value, so I'd call our little exercise in using the drag equation a resounding success any day.
 
  • Like
Likes ChessEnthusiast and SlowThinker
  • #13
ChessEnthusiast said:
Could you help me to write this equation? I've never done that before. Physics is not part of my college course, I'm simply an enthusiast.

Let's say that assuming a constant drag is very erroneous, then we come in with calculus.
Now, from the equation
F=½CρAv² —(i)
F=(mv–mu)/t —(ii)
To an infinitesimal point eqn (ii) becomes F=m(δv/δt) and eqn(i) becomes δF/δv=CρAv ∴ δF=CρAvδv, say eqn(iii)
From eqn(ii) δv=Fδt/m, say eqn(iv)
Put eqn(iv) in eqn(iii), eqn(iii) becomes δF=CρAv(Fδt/m).
Now F=∫ FCρAvδt/m with upper and lower limit being tfinal and tinitial respectively
Then
F=[(FfinalCρAvfinaltfinal)/m]+k] –[(FinitialCρAvinitialtinitial)/m]+k] say eqn(v). But for initial velocity in this case, tinitial=0
∴F=FCρAvt/m
m=CρAvt ∴ t=m/(CρAv), luckily same as you wrote. But note that the v is final velocity, not initial. If its initial that implies that the faster its start the quicker it stops. That's the error in your analysis which caused a very wrong value, and not because drag force reduces.
It makes sense, since it says the ball will never stop(by replacing zero as v says time is infinite). If the velocity reduces the force reduces "squarely". As it is reducing the force is not sufficient to bring it to rest since it also reduces, hence continues forever.
However, this may be untrue because if its get slow enough it instead obeys stokes law which is F=6πrηv.

Some of the parameters are still erroneous.
0.5m in radius? that's more that 12 inches as radius only ie diameter is 1m that's too large. 300 kg is thrice the human weight, are you saying 6 people needs to load the cannon? (Average human carries half his weight). And the cross-sectional area is πr² not 2πr².

Using your parameters, the eqn only that for the ball to get to 1m/s it will take about 677 seconds, which make sense. The only problem to this eqn I noticed is that it does not depend on initial velocity. Nevertheless there seem to be a remedy, we could fine the velocity after some short time rather than the instantaneous initial velocity where t tends to 0. After which we compute the drag force for that velocity, and insert it in eqn(v).

With brotherly love, let others comment on this method and eqn to be certain of its credibility. Thank you
Zaya Bell
 
  • Like
Likes ChessEnthusiast

FAQ: Cannonball - time required to stop its horizontal motion

1. How does the time required to stop a cannonball's horizontal motion vary with its initial velocity?

The time required to stop a cannonball's horizontal motion is directly proportional to its initial velocity. This means that the higher the initial velocity, the longer it will take for the cannonball to come to a complete stop.

2. Does the mass of the cannonball affect the time required to stop its horizontal motion?

Yes, the mass of the cannonball does affect the time required to stop its horizontal motion. A heavier cannonball will have more inertia and will take longer to come to a stop compared to a lighter cannonball with the same initial velocity.

3. How does air resistance impact the time required to stop a cannonball's horizontal motion?

Air resistance can significantly affect the time required to stop a cannonball's horizontal motion. The higher the air resistance, the more force it will exert on the cannonball, causing it to slow down faster and ultimately require less time to stop.

4. Is the angle of launch important in determining the time required to stop a cannonball's horizontal motion?

Yes, the angle of launch can greatly impact the time required to stop a cannonball's horizontal motion. If the cannonball is launched at an angle, it will have both horizontal and vertical components of motion, which can affect the time it takes to stop as well as the distance it travels.

5. How does the surface the cannonball lands on affect the time required to stop its horizontal motion?

The surface the cannonball lands on can affect the time required to stop its horizontal motion. A smoother surface will have less friction, allowing the cannonball to travel further and take longer to stop compared to a rougher surface with more friction.

Back
Top