Configuring LinkSys BEFW 11S4 Wireless Router

  • Thread starter Thread starter alanveron
  • Start date Start date
  • Tags Tags
    Router Wireless
Click For Summary
SUMMARY

The discussion centers on configuring the LinkSys BEFW 11S4 Wireless Router. Users are instructed to access the router's configuration page by entering the IP address http://192.168.1.1 in a web browser after connecting via an Ethernet cable. It is emphasized that the wireless access point is typically disabled upon initial setup, necessitating a wired connection for configuration. Additionally, users are advised to consult the router's manual for detailed setup instructions and are reminded that bandwidth distribution among connected devices is managed by the router's NAT functionality.

PREREQUISITES
  • Understanding of IP addressing, specifically private IP ranges like 192.168.1.1
  • Basic knowledge of Ethernet connections and network configuration
  • Familiarity with accessing router settings through a web browser
  • Awareness of NAT (Network Address Translation) and its impact on bandwidth sharing
NEXT STEPS
  • Research how to access and configure LinkSys routers, focusing on the BEFW 11S4 model
  • Learn about the implications of NAT on bandwidth distribution among devices
  • Explore troubleshooting steps for connectivity issues when accessing router settings
  • Investigate advanced bandwidth management techniques, such as Packetshaper or Cisco NBAR
USEFUL FOR

This discussion is beneficial for home network users, IT professionals, and anyone setting up or troubleshooting a LinkSys BEFW 11S4 Wireless Router.

alanveron
Messages
45
Reaction score
0
wireless router...

i bought a new wireless router from LinkSys...model no. is BEFW 11S4...i was asked to go to http://192.168.1.1 to configure my connection...but i can't even go to http://192.168.1.1...so how can i configure my connection?
Must i go to the site to configure it or i can configure it manually without visiting the site?
 
Last edited by a moderator:
Computer science news on Phys.org
did you get issued an IP address from the Wifi Router?

Open CMD and type ipconfig to find out, look for the default gateway, this will be your wifi router... open IE and put in the this IP address to configure the router...
 
IIRC, the wireless access point is not turned on when you initially turn the router on. You'll need to actually plug into it with an ethernet cable to be able to set it up and turn the wireless access point on.

- Warren
 
Remember that 192.168.1.1 is not a site on the Internet. It is the IP address that your router assumes on your home network.
 
so how to configure it?
 
Plug a cable into it, then direct a browser to http://192.168.1.1, then follow directions. Ask specific questions, please.

- Warren
 
Last edited by a moderator:
yeh good point, I thought he had pluged in an ethernet cable :-/
 
alanveron said:
so how to configure it?
No offense, but most manuals have quite specific and easy to follow directions...
 
russ_watters said:
No offense, but most manuals have quite specific and easy to follow directions...

True. And Linksys has pretty good tech support, I've dealt with them in the past and had no problems.

Just don't ask them the meaning of life.
 
  • #10
uhmmm, what is "the meaning of life" ? as your post mentioned ?
 
  • #12
i am using wireless router now to link to 2 of my pc...so can i configure one of the pc to be faster on surfing the net?
 
  • #13
unless you want to use a Packetshapper or some Nbar on a router (cisco) you will find it difficult giving one PC morebandwith than the other, typically any PC behind a NAT device will share the bandwidth at the NAT device...
 

Similar threads

How to route internet traffic via LAN port on a home router
  • · Replies 1 ·
Replies
1
Views
517
Wireless Router, WiFi, and a laser cutter
  • · Replies 24 ·
Replies
24
Views
4K
Can Wireless Routers Wear Out Over Time?
  • · Replies 11 ·
Replies
11
Views
2K
Configuring WiFi router with PPPoE and static IP
  • · Replies 3 ·
Replies
3
Views
2K
Solving Linksys EA6100 Modem Issue
  • · Replies 19 ·
Replies
19
Views
3K
Raspberry Pi 5 -- Start up USB Wifi Dongle on boot
  • · Replies 2 ·
Replies
2
Views
502
Connect my Canon MX922 printer to my new wireless router
  • · Replies 3 ·
Replies
3
Views
14K
Cisco Packet Tracer: Tool for Networking & CCNA Study
  • · Replies 1 ·
Replies
1
Views
2K
Which side of a wireless repeater to connect to?
  • · Replies 1 ·
Replies
1
Views
3K
Troubleshooting Unable to Access Router for Security Setup
  • · Replies 4 ·
Replies
4
Views
3K