Setting up wind power equipment

AI Thread Summary
To set up wind power for a home, essential equipment includes a wind turbine, inverter (which converts DC to AC), battery bank, circuit breaker box, and wiring. The inverter is necessary to manage the DC output from the turbine and integrate it with the home's electrical system. It's important to follow safety regulations outlined in the National Electric Code (NEC) and understand that disconnecting from the grid entirely can be challenging with DIY kits. Additionally, remaining connected to the grid can allow for selling surplus energy back to the power company. Researching power generation principles and building a prototype can enhance understanding and safety in the setup process.
freenergy4us
Messages
2
Reaction score
0
I'm a beginner at this but I'm an aspiring student of the electrical field. Electrical engineer, electrician, electronics technician. I like it all.

My question is what equipment, other than what I know already, do I need to run as much of my house off of wind power?

Wind turbines or anything that spins basically.

I know I need a converter but I want to know why I need it besides the fact that it converts DC to AC. Just a little more explanation is all. I know a little about it.

Probably a transformer. Explain why.

A circuit breaker box. Explains itself.

And wires.

What else do I need? Is there a site that can show this in a diagram?
 
Engineering news on Phys.org
Why don't you tell us a little more about what you already know - maybe provide some details and ask more specific questions?
 
your 'converter' and transformer are a single system called an inverter. and you need it because a wind turbine will generate DC power. you then use the DC output to charge a battery bank. the battery bank then feeds the inverter which you tie into your houses supply. you cannot just go to Walmart and buy a 5kw inverter and tie it in, you will need a GTI (grid tie-in) inverter or synchronous inverter. if you are in the states you will want to pick up a copy of the National Electric Code (NEC) and do some reading in there. i don't know what the regulations are pertaining to wind generation but I am sure there is a section in there and anything the NEC puts regulations in for, there is a good reason.
 
Okay I know only what I've read so far from websites etc. I'm looking for diagrams like this

http://cgi.ebay.com/SOLAR-HOME-KIT-PANELS-CONTROLLER-BATTERY-INVERTER-/380288742901?pt=LH_DefaultDomain_0&hash=item588af9b5f5

And these pictures and videos are pretty good. http://mdpub.com/Wind_Turbine/

So why is it that some things need a converter and others don't like a solar water sprinkler?

I just need to know how to hook things up to get free wind power and disconnect from the grid completely if possible. But I think I may have found what I need, so thanks.
 
disconnecting from the grid entirely will prove difficult using a DIY generation 'kit'. and you will not do it with a $600 ebay kit. i have never looked into a solar sprinkler but it must be a DC sprinkler to not need an inverter. it sounds as if you do not know many of the principles behind what you are trying to do which makes it dangerous. also remaining on the grid could prove beneficial if you do end up generating sufficient power since any surplus energy you generate can be sold back to your power company.

do a little research on power generation and how wind/solar collectors work and maybe build a bench top prototype to gain some familiarity with what you are doing. you can find a lot of information on these topics on google.
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top