Transmission line and measuring Zo

15 replies · 4K views · last reply
TheRedDevil18
Messages
406
Reaction score
2

Homework Statement


Cross-section diagram of cable dimensions: two coaxial cable pairs labelled Unit 1 and 2 with 1.4mm spacing and 0.6mm core/conductor dimensions, and Unit 3 and 4 with 1.0mm spacing and 0.5mm dimensions, captioned Figure 1. Cable Dimensions.

Figure 2:
Circuit diagram of a measurement setup: a 50 ohm signal generator with source resistance Rs and source Vs, a matching/sensing impedance RM, a twisted pair transmission line with input impedance Zi, and a load RL, with measurement points V1, V2 and V3 marked.


Homework Equations

The Attempt at a Solution



3.2) I made an equation for the input voltage and input current
Vi = Vs*(Zi)/(Zi+Rs+Rm)

Ii = Vs/(Zi+Rs+Rm)

I am a bit confused about what voltages V1 and V2 are measuring, and what do they mean by using the phase ?, I don't know the phase

3.3) After some research I found this equation for a twisted pair cable

Diagram of a twisted-pair cross-section showing two circles, each with a dark blue conductor and light blue insulation, labelled S = 1.3 mm (minimum) and D = 0.95 mm; formula Z_DIFF = (120/sqrt(e_R)) ln(2S/D) with variable definitions and example 2S/D = 2(1.3)/0.95 = 2.736.


Though I'm not sure what to use for Er. On the site it says
εR=(c/v)^2

but I don't know the velocity of the signal

http://www.sigcon.com/Pubs/edn/TwistedImpedance.htm
 
TheRedDevil18 said:

Homework Statement


View attachment 104936
Figure 2:
View attachment 104937

Homework Equations

The Attempt at a Solution



3.2) I made an equation for the input voltage and input current
Vi = Vs*(Zi)/(Zi+Rs+Rm)

Ii = Vs/(Zi+Rs+Rm)

I am a bit confused about what voltages V1 and V2 are measuring, and what do they mean by using the phase ?, I don't know the phase

3.3) After some research I found this equation for a twisted pair cable

Diagram of two twisted-pair cross-sections with dark blue conductors inside light blue insulation, labeled S = 1.3 mm (minimum) center spacing, D = 0.95 mm conductor, and 1.3-mm insulation; beside it, the formula Z_DIFF = (120 / sqrt(e_R)) ln(2S/D) with a note defining the terms and the example 2S/D = 2(1.3)/0.95 = 2.736.


Though I'm not sure what to use for Er. On the site it says
εR=(c/v)^2

but I don't know the velocity of the signal

http://www.sigcon.com/Pubs/edn/TwistedImpedance.htm
No none else answering yet, this is my best shot:-
1) One of the methods of finding Zo is from Zo = SQRT (Zoc * Zsc)
To find Zsc and Zoc, the test circuit is used to find an unknown impedance.
I am a simple person, so I think you can solve the test circuit using a phasor diagram, but it is a bit complicated. Take Ii as the reference, as it is a series circuit, and then V50, Vrm and V2 will add up vectorially to Vs. V50 and Vrm are in phase with Ii and are found from Ii using Ohm's Law. Then the complex ratio of V2/Ii give the cable input impedance.
2) The question is very weak on the matter of dielectric, because the conductors have only a thin covering and are not embedded in the dielectric. So we presume Er may lie somewhere between air=1 and polyethylene=2.3.
You have my total sympathy with this laborious question.
 
tech99 said:
No none else answering yet, this is my best shot:-
1) One of the methods of finding Zo is from Zo = SQRT (Zoc * Zsc)
To find Zsc and Zoc, the test circuit is used to find an unknown impedance.
I am a simple person, so I think you can solve the test circuit using a phasor diagram, but it is a bit complicated. Take Ii as the reference, as it is a series circuit, and then V50, Vrm and V2 will add up vectorially to Vs. V50 and Vrm are in phase with Ii and are found from Ii using Ohm's Law. Then the complex ratio of V2/Ii give the cable input impedance.
2) The question is very weak on the matter of dielectric, because the conductors have only a thin covering and are not embedded in the dielectric. So we presume Er may lie somewhere between air=1 and polyethylene=2.3.
You have my total sympathy with this laborious question.

Thanks for the reply, I have a few questions,

By V50, You mean the the signal generator impedance voltage ?
V2 is measuring the input voltage to the transmission line or the input impedance voltage ?
And what voltage is V1 measuring ?
 
TheRedDevil18 said:
Thanks for the reply, I have a few questions,

By V50, You mean the the signal generator impedance voltage ?
V2 is measuring the input voltage to the transmission line or the input impedance voltage ?
And what voltage is V1 measuring ?
V50 is the voltage across Rs.
V2 is the voltage across the line at its input point.
V1 is the voltage across the output terminals of the signal generator.
 
TheRedDevil18 said:
Though I'm not sure what to use for Er. On the site it says
εR=(c/v)^2
but I don't know the velocity of the signal
Assume air as the dielectric. What is εr for air?
Also assume lossless line.
There is a formula stating that V2 = V2(V3, θ, Z2, Z0).
θ = βx, γ = jβ and x = physical line length. So θ is unknown.
But you know V2, V3 and Z2 for 2 cases so you have 2 equations and 2 unknowns so you can solve for γ and Z0.

These of course are all phasors, i.e. voltages with attendant phase shifts.
 
rude man said:
Assume air as the dielectric. What is εr for air?
Also assume lossless line.
There is a formula stating that V2 = V2(V3, θ, Z2, Z0).
θ = βx, γ = jβ and x = physical line length. So θ is unknown.
But you know V2, V3 and Z2 for 2 cases so you have 2 equations and 2 unknowns so you can solve for γ and Z0.

These of course are all phasors, i.e. voltages with attendant phase shifts.
I don't think we are given the line length and velocity factor.
 
Can't I just use a voltage divider ?

V2 = Vs*(Zin)/(Zin+Rs+Rm)

Since we know V2, Vs, Rs and Rm we can calculate Zin
 
TheRedDevil18 said:
Can't I just use a voltage divider ?

V2 = Vs*(Zin)/(Zin+Rs+Rm)

Since we know V2, Vs, Rs and Rm we can calculate Zin
This not accurate because Zin is possibly reactive.
 
tech99 said:
I don't think we are given the line length and velocity factor.
As I said, line length x is an unknown. But you will solve for θ so forget x. x and θ are related per what I gave you.
 
TheRedDevil18 said:
Can't I just use a voltage divider ?

V2 = Vs*(Zin)/(Zin+Rs+Rm)

Since we know V2, Vs, Rs and Rm we can calculate Zin
How do you propose to solve for Z0 and γ?
 
rude man said:
How do you propose to solve for Z0 and γ?

I forgot to note that the length of the transmission line is known, 56m. Their is a formula for calculating Zo
Formula Zo equals the square root of the product Zoc times Zsc, with Zo, Zoc and Zsc as subscripted impedance symbols.


So Zsc would be the input impedance I measure when the load is short circuited. And Zoc would be the input impedance I measure when their is no load

Equation: Z_in = Z_o (Z_L + Z_o tanh(γl)) / (Z_o + Z_L tanh(γl)), with Z_in, Z_o, Z_L, γ and l as symbols.


Equation for a lossless transmission line: gamma = j beta, Zin = Zo (ZL + j Zo tan beta l) / (Zo + j ZL tan beta l).


And for a open circuit line,
Equation for open-circuit input impedance: Z_in = Z_oc = Z_o / (j tan βl) = -j Z_o cot βl.


And for short circuit,
Equation Zin = Zsc = jZo tan βl, giving the input impedance of a short-circuited lossless transmission line as a purely imaginary value.


So once I have found Zoc and Zsc and hence Zo, I can use one of the above equations to calculate Beta = Gamma
 
rude man said:
How do you propose to get β?

By finding the input impedance, for example Zsc using the voltage divider equation
V2 = Vs*(Zin)/(Zin+Rs+Rm)

Then finding Zoc, using the same equation but for open circuit

Then Zo, using this equation
Equation: Zo equals the square root of the product of Zoc and Zsc, written as Zo = sqrt(Zoc * Zsc).


And since I have Zsc and Zoc, I can use either of the equations I listed above to solve for Beta
Equation: Zin = Zsc = j Zo tan βl, where Zsc is the short-circuit input impedance of a transmission line.


I have the length of the line = 56m
 
TheRedDevil18 said:
I forgot to note that the length of the transmission line is known, 56m. Their is a formula for calculating Zo
View attachment 104974

So Zsc would be the input impedance I measure when the load is short circuited. And Zoc would be the input impedance I measure when their is no load

View attachment 104970

View attachment 104971

And for a open circuit line,
View attachment 104972

And for short circuit,
View attachment 104973

So once I have found Zoc and Zsc and hence Zo, I can use one of the above equations to calculate Beta = Gamma
Looks good now RedDevil!