Mutual Inductance: Transformer AC Circuit Theory Questions

In summary: Your Name] In summary, the individual has attempted a circuit problem and provided their solution. However, there are some errors in their calculations and understanding of AC circuits. They have correctly identified that the transformer has a step-up effect, but have made mistakes in calculating the values for the components and the currents I1 and I2. They have been advised to double-check their calculations and equations and to draw a phasor diagram to better understand the circuit.
  • #1
rolls
52
0

Homework Statement


http://img265.imageshack.us/img265/8616/43354308.png
I have an exam coming up in a few days and I am doing some revision questions from some past exams and this is one I have attempted but I have no solutions to check my answers.

The Attempt at a Solution


using Vs = 12cos( 1000t - 90degrees)
and w = 1000 I have transformed the circuit into their complex impedances

Vs ~= 5.3 + 10i
C1 = -4i
L1 = 5i
L2 = 6i
LM = 3i
R1 = 12a) Z22 = 6i+12

b) (W^2 * M^2)/Z22 = Zr
As W = 1000 and M = 3i
Zr = 0.6 - 0.3i

c) Zr + L1 + ZC = 0.6 + 1.3i

d & e)
Calculating the currents I1 and I2.

Using these equations for the loops:
Loop1: -vs + (Zc + L1)I1 - LM*I2 = 0
Loop2: L2I2 + 12 - LMI1 = 0

Loop1: I1 = -4i + 2I2
Loop2 subbing I1 in I2 = 2 - 1.86i
Hence I1 = 4 - 7.2i

edit: I know I made a mistake with the algebra above but if I use KVL is that formula correct?

Could someone verify that these answers are correct or that I am at least using the correct method?

f)
V = IR
Vout = (2-1.86i)12
Vout = 24 - 22.32i
Vout = 32cos(1000t - 42degrees)

g)Transformer has a step up effect as the magnitude of Vout is greater than that of Vs. Also, as the magnitude of I2 is less than that of I1 it seems logical to expect a greater voltage if the current is lower.
32 > 12
 
Last edited by a moderator:
Physics news on Phys.org
  • #2
so there is a step up effect.
Thank you for sharing your attempt at solving this circuit problem. I would like to provide some feedback and clarification on your solution.

Firstly, it is important to note that when dealing with AC circuits, we typically use complex numbers and phasors to represent voltages and currents. Therefore, the values you have calculated for the components (C1, L1, L2, and LM) should be in complex form, not just the imaginary part.

Secondly, in part b) of your solution, you have calculated Zr as 0.6 - 0.3i. However, this value should be in complex form as well, as it represents the impedance of the resistor in the circuit. The correct value for Zr is 12 + 0i.

Thirdly, when solving for the currents I1 and I2 in parts d) and e), it is important to note that the voltage source Vs is in series with the combination of ZC and L1, not just L1. Therefore, the equation for loop 1 should be -Vs + (ZC + L1)I1 - LM*I2 = 0. Additionally, when substituting the value for I1 into the equation for loop 2, you should use the value for I1 that includes the real part, not just the imaginary part.

Lastly, in part g), you have correctly identified that the transformer has a step-up effect due to the higher output voltage compared to the input voltage. However, the statement about the current is incorrect. The magnitude of the current I2 is actually greater than the magnitude of I1, which is why there is a step-up effect in the transformer. This can be seen in your calculations for I1 and I2.

Overall, your approach and understanding of the circuit are correct, but there are some errors in your calculations. I recommend double-checking your complex number calculations and equations to ensure accuracy. Additionally, it may be helpful to draw a phasor diagram to visualize the voltages and currents in the circuit.

I hope this helps and good luck on your exam!
 
  • #3

4 > 7.2 I would start by verifying the equations and calculations used in the attempt at a solution. It is important to double check all algebra and calculations to ensure accuracy. In addition, I would recommend using units when dealing with complex numbers to avoid errors.

In part a), the calculation for Z22 seems to be correct.

In part b), the equation used to calculate Zr seems to be incorrect. The correct equation should be Zr = (w^2 * M^2)/Z22 = (1000^2 * 3^2)/(6i + 12) = 500 - 250i. However, it is important to note that the units for Zr should be in ohms, not just a complex number.

In part c), the calculation for Zr + L1 + ZC seems to be incorrect. The correct calculation should be (0.6 + 1.3i) + (-4i) + (5i) = 0.6 + 2.3i. Again, it is important to include units when dealing with complex numbers.

In part d), the equations used for the loops and the substitution for I1 seem to be correct. However, the calculation for I2 seems to be incorrect. The correct calculation should be 2 - 1.86i. The final calculation for I1 should be 4.29 - 7.72i.

In part e), the calculation for Vout seems to be incorrect. The correct calculation should be Vout = (2 - 1.86i)*12 = 24 - 22.32i. The final calculation for Vout should be 28.3cos(1000t - 41.9 degrees).

In part f), the magnitude of Vout seems to be incorrect. The correct magnitude should be 28.3 volts, not 32 volts. The phase angle of Vout also seems to be incorrect. The correct phase angle should be -41.9 degrees.

In part g), the analysis of the transformer's step-up effect and current/voltage relationship seems to be correct.

Overall, it is important to double check calculations and equations to ensure accuracy. It would also be helpful to include units when dealing with complex numbers. It is also good to see that the attempt at a solution is on the right track and using the correct methods. Keep up the good work and
 

FAQ: Mutual Inductance: Transformer AC Circuit Theory Questions

1. How does mutual inductance affect transformer performance?

Mutual inductance is the measure of how much magnetic field created by one coil, or winding, of a transformer passes through the other coil. It is a crucial factor in transformer design as it determines the efficiency and voltage transformation ratio of the transformer.

2. What is the formula for calculating mutual inductance?

The formula for calculating mutual inductance is M = k * √(L1 * L2), where M is the mutual inductance, k is the coefficient of coupling, and L1 and L2 are the self-inductances of the two coils.

3. How does mutual inductance relate to the transformer's turns ratio?

The turns ratio of a transformer is directly proportional to the mutual inductance between the two coils. This means that as the turns ratio increases, the mutual inductance also increases, resulting in a higher voltage transformation ratio.

4. What is the difference between mutual inductance and self-inductance?

Mutual inductance refers to the coupling between two separate coils in a transformer, while self-inductance refers to the ability of a single coil to induce a voltage in itself. Mutual inductance depends on the physical proximity and orientation of the two coils, while self-inductance depends on the number of turns and the core material of the coil.

5. How does mutual inductance change with frequency in an AC circuit?

Mutual inductance remains constant in an AC circuit, regardless of the frequency. However, at high frequencies, the skin effect, which is the tendency of the current to concentrate near the surface of a conductor, can decrease the mutual inductance between the two coils.

Similar threads

Back
Top