Fuji Inverter E9s Series Parameter Setting

  • Thread starter Thread starter levoeg
  • Start date Start date
  • Tags Tags
    Parameter
AI Thread Summary
Users are seeking assistance with parameter settings for the Fuji Inverter E9s series, noting that there are over 70 parameters to configure. One user expressed difficulty in achieving proper results despite trying several settings. Another participant provided a link to a PDF that contains some information but emphasized the need to consult the official instruction manual for detailed parameter settings. The user seeking help does not have access to the manual since the inverter was not installed by them and noted that Fuji Electric requires recommendations from the original installers for support. The discussion highlights the challenges faced when lacking documentation for technical equipment.
levoeg
Messages
6
Reaction score
0
dear all
can anyone help me to find parameter setting (or description )of fuji inverter E9s series
desperately i need this.

thanx in advance
levoeg
 
Engineering news on Phys.org
levoeg said:
dear all
can anyone help me to find parameter setting (or description )of fuji inverter E9s series
desperately i need this.
thanx in advance
levoeg
http://www.atrump.com/Inverter/E9s.htm"
 
Last edited by a moderator:
thanx

Hi dlgoff
thank you very much for your reply. there is more than 70 parameters do you have the description of that. actually i am using it for some other applications. i tried with 06,07,08 but still i couldn't get proper result that why i am asking you.
anyway once again i thank you for your quick reply

regards
Levoeg...
 
I did a little searching but all I could find was a PDF file for the "www.elta.com.cn/download/pdf/meh404a.pdf"[/URL].
At the bottom of the previous link I gave was this: "The operator has to refer to the Fuji FVR-E9S Inverter Instruction Manual for Par setting." You may have to give them a call.
Regards
 
Last edited by a moderator:
thank you dlgoff,
actually this is not installed by us, so i don't have any manual for this,
fuji electric won't support us unless the people installed this will recommend us. anyway i try my best.

thanx and happy holidays
regards
levoeg
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Self excited induction generators and grid connected solar inverters?
Replies
9
Views
2K
What Are the Electromagnetic Parameters of Carbon Fiber for CST Simulations?
Replies
4
Views
2K
I Parameters of the rough surface (for electromagnetic scattering)
Replies
2
Views
2K
Reparameterizing a curve in path length parameter
Replies
1
Views
2K
A Computing the Fisher Matrix numerically
Replies
1
Views
2K
The simulation of a microwave antenna made of nanofilm Ti3C2 (Mxene)
Replies
21
Views
5K
Can Nonlinear Equation Fitting Yield Reliable Parameters for Varying Data?
Replies
6
Views
1K
In need of VFD/Inverter to motor assistance please
Replies
15
Views
4K
Calculate the max current for a powerline
Replies
22
Views
4K
Basic T parameter table for RF design
Replies
2
Views
3K

Hot Threads

Recent Insights

Back
Top