How do you determine when a diode is forward or reverse biased in a clipper circuit?

  • Thread starter ranju
  • Start date
  • Tags Tags
    Circuits
17 replies · 2K views · last reply
ranju
Messages
221
Reaction score
3
In the given circuit. It was given that when Vi>Vr diode will be reverse biased or off..and when Vi<Vr diode will be forward biased... but I am not getting how we infer this..??It may sound a very basic question but its not clear...I am not able to decide it
 
Attachments
  • Hand-drawn clipper circuit: source Vi with diode D in series, feeding a load resistor RL and a capacitor-like element labelled VR to ground, with output Vo marked across the parallel branch.
    IMG_20141019_151209.jpg
    22.2 KB · Views: 469
I have no idea about this.. actually I am not getting the use of the battery Vr..!
 
Battery (Vr) is nothing more than a voltage source. You are not familiar with a voltage source?

As for the diode. Diode allows current to flow only in one direction (called the diode's forward direction), while blocking current in the opposite direction (the reverse direction).

Diode I-V characteristic graph of I_D (typically mA) against V_D, showing forward bias above 0.7 V with 10 mA marked, reverse current I_R in nA, and reverse breakdown near -1000 V, with forward and reverse bias symbols.


Forward-biased diode (diode is ON)
Circuit schematic of a 10V battery in series with resistor R1 (930 ohm) and a forward-biased diode, with forward current IF = 10mA, VR1 = 9.3V and VF = 0.7V labelled.
Reverse-biased diode (diode is OFF)

Circuit diagram of a 10V battery in series with resistor R1 (470 ohms) and a diode, labelled with reverse current IR = 0A and reverse voltage VF = 10V = reverse voltage across the diode, with 0V across R1.
 
zoki85 said:
IR isn't 0. It is just small.
Well yes, but I don't want to confuse the OP. And you can read from the first picture the reverse current is typically in nanoamps range
 
yes I know Vr is voltage source ,but here it is affecting the bias of diode whether forward or reverse..but how its being decided.
 
If we set Vin = 0V, then you can replace Vin with a short wire.
So the circuit will looks like this:

Two circuit schematics side by side: left shows source Vi feeding diode D1, then load RL in series with battery VR across output Vo; right shows the same circuit with Vi replaced by a short wire, labelled Vi = 0V.

And now can you tell me in which state the diode is, ON or OFF? And Vo is ?
 
Last edited:
Yes, diode is reverse biased. But what about Vo voltage? Any clues?
 
its in rever biase ..so it'll be open , so output V0 will be Vr..>!
 
no..actually considering the polarity of battery , V0 will be -Vr.
 
Yes, very good Vo = -vr. So if we assume that Vr = 2V then Vo = -2V

OK, so now let as try to find Vo if Vi is larger than 0V. For example Vi = 5V

Clipper circuit schematic: input source Vi with a diode D1 in series, a resistor RL of 1K and a reference battery VR of 2V in parallel with the output Vo, with 5V marked across the diode.


The voltage at cathode is 5V and the voltage at anode is -2V. So voltage across the diode is equal to Vd = -2V - 5V = -7V.
And this means that diode is OFF(Reverse-biased) and Vo = -2V.

Now let as change the polarity of the Vi voltage source from +5V into -5V.

Clipper circuit schematic: source Vi with -5V on top, D1 diode conducting left to right, node at -4.3V feeding load RL 1K in parallel with reference VR 2V, output Vo across the node, 2.3mA branch current and 0.7V across the diode.


This time diode is forward biased because Vd is positive. Vd = Vo - Vi = -2V - (-5V) = 3V. And this is why the diode will conduct current.
And Vo = -4.3V.
So we can conclude that the diode will be ON only if input voltage (Vi) is 0.7V voltage lower than Vr voltage.
Diode is ON if Vin < -2.7V
 
  • Like
Likes   Reactions: ranju
but if we take Vi=1V then diode will be reverse biase even if Vi=-1V.. since Vd= -2-(-1)=-1V..so it will not conduct..!
 
Jony130 said:
So we can conclude that the diode will be ON only if input voltage (Vi) is 0.7V voltage lower than Vr voltage.
Diode is ON if Vin < -2.7V
I did'nt get this point..how can you generalise it.>??
 
ranju said:
but if we take Vi=1V then diode will be reverse biase even if Vi=-1V.. since Vd= -2-(-1)=-1V..so it will not conduct..!
Yes exactly. Diode will conduct only if Vin is lower than -2.7V

ranju said:
I did'nt get this point..how can you generalise it.>??
What you don't understand here?
When diode conduct, the voltage drop across the diode is around 0.5V...0.7V.
This means that Vin voltage must be 0.7V lower than Vr voltage to force diode to conduct.
For Vr = 2V input voltage need to be lower than -2.7V
 
Last edited:
ohkk ..so for solving the clipper circuits.. we should proceed in this way only..?? I mean assuming values of unknowns ( Vr & Vin)..then find the bias of diode..??
 
No it is not necessary, but this "method" help us visualize the situation much better.