LED indicator circuit below 11V with common cathode tri-color LED

6 replies · 3K views · last reply
jmcafee
Messages
4
Reaction score
0
Your opinion, please. Does one of the two variations of this circuit offer a clear advantage, or is it a wash (see attached)?

This indicator circuit turns on the LED below 11V (set by the zener). The LED cathode must be at ground (it is actually part of a tri-color LED with a common cathode), so it cannot be in the collector circuit of an NPN.

Any suggestions on the transistor biasing?

Thanks for your comments.
 
Attachments
  • Two schematic versions of a low-voltage LED indicator circuit, Version A on top and Version B below, each with transistors Q1, Q2 or Q3, resistors R1 to R5, zener diode D1 and LED D2 to 0V.
    Schematic.gif
    6.8 KB · Views: 557
The 2nd circuit is closest, but still not quite right. Thematically, you use a PNP BJT for high-side switches, as the 2nd circuit does. But the first NPN transistor Q1 should have its collector connected to Q3's base through the resistor, so that when Q1 turns on, it pulls down on Q3's base to turn it on. Re-draw the 2nd circuit that way, and re-simulate. Should work a lot better.

Welcome to the PF, BTW!
 
Thinking further about what you said, I'm not sure that your proposed action is what I need functionally (or maybe I don't understand). To reiterate, the LED is to be OFF above 11V.

I'm using Q1 as an inverter; when it is on, I want Q3 off (and the reciprocal). So I don't want to pull the Q3 base low when Q1 is saturated.
 
Last edited:
jmcafee said:
Thinking further about what you said, I'm not sure that your proposed action is what I need functionally (or maybe I don't understand). To reiterate, the LED is to be OFF above 11V.

I'm using Q1 as an inverter; when it is on, I want Q3 off (and the reciprocal). So I don't want to pull the Q3 base low when Q1 is saturated.

Ah, my bad, I missed where you mentioned the polarity. But circuit #2 still won't work, because Q1 can't pull its emitter up high enough to turn off Q3, given its base biasing. I'd suggest using an additional transistor instead -- use the configuration I mentioned in my previous post, and add an extra NPN stage in the middle to do the inversion.
 
Mike,

Thanks very much! This may not be exactly what you envisioned, but I'm sure it is close. Regardless, it now functions perfectly (my original design would never turn off the red LED).

I've attached the full schematic. It is a voltage monitor using a single LED indicator that lights red at 10-11.2V, amber at 11.2-12.2V, and green above 12.2V.

I learned an important lesson from you that high side switching is trickier to design than low side switching.

Jim
 
Attachments
  • Schematic of a voltage indicator circuit with transistors Q1 to Q4, zener diode D1 rated 12V, resistors R1 to R9, a red and green LED pair D2 and D3, and a chain of diodes D4 rated 10V, D5 and D6 on the right; supply labelled Vs 10-13V and 0V ground.
    Schematic full.gif
    15 KB · Views: 574
jmcafee said:
Mike,

Thanks very much! This may not be exactly what you envisioned, but I'm sure it is close. Regardless, it now functions perfectly (my original design would never turn off the red LED).

I've attached the full schematic. It is a voltage monitor using a single LED indicator that lights red at 10-11.2V, amber at 11.2-12.2V, and green above 12.2V.

I learned an important lesson from you that high side switching is trickier to design than low side switching.

Jim

Nice work, Jim. I'd say you have a future in circuit design! :biggrin: