Methodology to done my project

  • Thread starter Thread starter no183
  • Start date Start date
  • Tags Tags
    Project
AI Thread Summary
The discussion focuses on a project involving numerical simulation of heat flow in a CPU casing using Fluent, specifically concentrating on forced convection. The user seeks guidance on conducting a literature review, asking about relevant theories, including whether to address turbulent or laminar flow, and the nature of the flow (internal or external). Key topics for the literature review include heat transfer principles, boundary layer theory, and relevant equations such as those related to energy, continuity, and Navier-Stokes. The importance of understanding basic theories and boundary conditions for successful simulation is emphasized. Overall, a solid grasp of these concepts is crucial for the project's success.
no183
Messages
15
Reaction score
0
ok, now i have just received a project regarding doing numerical simulation regarding heat flow in my CPU casing using fluent.
my scope of the project is just based on forced convection only
so now, i am doing my literature review part, any past study i can refer to?
adding detail..
i need to know what kind of thing i should included in literature review section here. theory? if theory what theory involved?
turbulent flow? or laminar is it?
is it an external or internal flow?
cause i just write regarding heat transfer (conduction, convection and radiation in the beginning of the chapter) follow by derivation of energy, continuity and navier stoke..
anything to add in?
note: kindly give me some theory to know first, i guess i am poor in this.. i don't know what theory related to my study
 
Engineering news on Phys.org
If you don't understand the basic theory, you have basically no hope of doing a numerical simulation. If you can't write a complete sentence, you can't write a paper that will receive a passing grade. Do you understand what a boundary condition is?
 
the layer which separate laminar and turbulent?
should i write boundary layer inside my litreature review?if yes which i should write? there is a lot of boundary layer type...
and what equation related to my project?
 

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Similar threads

What is the temperature loss along a duct with hot air entering?
Replies
24
Views
3K
Creating turbulence in a small tube
Replies
4
Views
2K
Calibrating Pump/Venturi (Air) in a Closed Recirculating Water System
Replies
1
Views
319
Laser Doppler Anemometry and CFD - 3rd Year Project
Replies
2
Views
2K
Calculating heat recovery from engine exhaust gases
Replies
2
Views
3K
Exam help regarding heat exchanger, forced convection questions
Replies
7
Views
3K
Patient Lifter Boom design for my ME Senior Project
Replies
18
Views
2K
Venturi Effect based thought experiment
2
Replies
58
Views
6K
Final Project (Matura Project) About The Wave Pendulum
Replies
2
Views
976
Boundary layer thickness confusion
Replies
7
Views
9K

Hot Threads

Recent Insights

Back
Top