Very specific question on current draw from a dc power supply

AI Thread Summary
Current drawn from a power supply is determined by the device's requirements, not the power supply's maximum rating; a 5V, 32A supply can provide up to 32A, but will only deliver what the device needs, such as 550mA. It is possible to use a 5V line from a computer power supply for projects like op amps or 555 chips, but the power supply must remain connected to the computer or modified correctly to function safely. Modifying a computer power supply can create a useful bench unit, but requires electrical expertise. Multiple ground leads in power supplies help distribute high current loads, reducing resistance and voltage drop. Using a common ground for low potential connections is generally acceptable for these applications.
matinm90
Messages
10
Reaction score
0
okay so I am just slightly confused about current and about how it is drawn from a power supply, so say we have a device that requires 5 volts and uses a max of 550 milliamps, and now let's say that the power supply used is rated at 5 volts, but 32 amps, does this mean that the power supply pushes out 32 amps regardless? or is current drawn by the device based on what it needs? forgive me if this question sounds obvious to some, but I am just a little confused about it, thanks in advance.
 
Engineering news on Phys.org
No, the power supply rated 5V and 32A mean it can provide up to 32A of current. If you draw only 0.5A, it is perfectly fine.
 
Okay so theoretically let's just say I wanted to use a 5 volt line from a power supply from a computer, would I be able to just connect the + and ground to a bread board to use with an op amp or 555 chip? I hope I explained the question clearly. And thank you, it was really helpful.
 
Yes, you can safely tap out the +5V and Ground from your computer and use it on the breadboard of 555.
 
Okay so theoretically let's just say I wanted to use a 5 volt line from a power supply from a computer,

You didn't say if this power supply was still in the computer.

You cannot simple take a power supply out of a computer, connect it to the mains and expect to use any of the voltage outputs - it simply won't turn on.

It is possible to modify a computer power supply to become a useful and cheap bench unit, but you will need greater electrical experience to accomplish this safely.

go well
 
Studiot said:
You didn't say if this power supply was still in the computer.

You cannot simple take a power supply out of a computer, connect it to the mains and expect to use any of the voltage outputs - it simply won't turn on.

It is possible to modify a computer power supply to become a useful and cheap bench unit, but you will need greater electrical experience to accomplish this safely.

go well
That depends on the PSU.

I can use the 5V supply on mine without any modifications, but as soon as I tried to use the -12V supply it tripped out.
 
Actually you can short the ps_on pin and a common ground pin to turn it on and yes it works I tried millions of times before. And thank you all for your help, but does anyone know why there are so many common ground leads on computer power suPplies? Lol. But thank you all for your helP.
 
Wall warts are very handy for this sort of thing. Everyone seems o have some of those, skulking about in a drawer somewhere. (Check the label to see what it should be delivering)
 
And thank you all for your help, but does anyone know why there are so many common ground leads on computer power suPplies?

very simply...
For the same reason that there is multiple +5 and +12V etc leads
it spreads the high current load anyone of those single small cables isn't going to carry the 10++ amps so you increase the number of wires to decrease the resistance and therefore decrease the voltage drop.

and yes, using computer power supplies outside of the computer is VERY easy to do. They make awesome hi current supplies.

cheers
Dave
 
  • #10
Oh okay I see, that makes perfect sense actually. Now if I needed to use a 5 volt low potential connection would the common ground be good enough? Cuz I'm used to the traditional low potential and high potential connections.
 
Back
Top