What Is the Initial Velocity of the Bullet?

  • Thread starter Thread starter PreetiM
  • Start date Start date
  • Tags Tags
    Block Bullet
AI Thread Summary
The discussion revolves around calculating the initial velocity of a bullet fired into a wooden block, along with the block's velocity post-impact and the energy lost during the collision. The bullet's mass is 0.007 kg, and it exits the block at 200 m/s, while the block, initially at rest, slides 0.5 m before stopping. The initial velocity of the bullet was calculated to be approximately 202.09 m/s using the work-energy theorem, while the block's velocity right after the impact was found to be 1.714 m/s. Energy loss during the collision was estimated at 2.94, although there was some confusion regarding the calculations for parts a and c. The conversation highlights the importance of using conservation of momentum for accurate results in inelastic collisions.
PreetiM
Messages
3
Reaction score
0

Homework Statement


A .007 kg bullet is fired into a 2 kg wooden block initially at rest on a level surface. The bullet passes through the block and emerges with the velocity of 200 m/s. The block slides .5 m and stops. If the coefficient of the friction between the block and and the surface is .3, find a) the initial velocity of the bullet, b) the velocity of the block right after being hit by the bullet and c) the energy loss of the bullet during the collision.

Homework Equations


I understand how to get part a of the question but I can't figure out the other two parts. Please help me :[.

The Attempt at a Solution


For part a I got 202.09 m/s.
 
Physics news on Phys.org
Welcome to PF!

Hi PreetiM! Welcome to PF! :wink:

Use the work energy theorem …

work done = change in kinetic energy …

show us what you get. :smile:​
 
Hello! Thanks for helping :)

So for part b) I used Fd= 1/2mvi2-1/2mvf2
and for the velocity of the block I got 1.714 m/s.

For part c) I just subtracted the final kinetic energy from the initial kinetic energy and got 2.94. I think that looks correct :P.
 
(b) looks correct. :smile:

I don't understand how you got (a) or (c) :confused: …

can you show your calculations?​
 
For a) I did what a peer tutor told me to do, he said
Initial Kinetic energy - work done by friction = final kinetic energy.

So I did, .5mvi2 - Ffrictiond = .5mvf2

When I solved for vi I got 202.089 m/s.

I admit for part c) I did just guess :(.
 
Either your peer tutor is wrong, or he was talking about part (b) not part (a). :redface:

For part (a), energy is not conserved (this is obviously not an elastic collision ).

Use conservation of momentum instead (you'll need the result from part (b) for this).
 
Thread 'Voltmeter readings for this circuit with switches'

Thread 'Voltmeter readings for this circuit with switches'

TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
View full post »
Thread 'Correct statement about a reservoir with an outlet pipe'

Thread 'Correct statement about a reservoir with an outlet pipe'

The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
View full post »

Similar threads

State whether the distance x for the block would be greater/less/same
Replies
25
Views
2K
Calculating Friction & Time for a Bullet Penetrating Rubber
Replies
2
Views
2K
Momentum Problem -- Bullet fired into a block of wood
Replies
2
Views
2K
Conservation of momentum in a bullet-block-spring system
Replies
6
Views
3K
Bullet shooting vertically into a block
Replies
9
Views
7K
A bullet pushing a knot out of a wood block
Replies
13
Views
3K
Is My Physics Calculation on Bullet and Block Interaction Correct?
Replies
14
Views
4K
MCAT Collisions of a wooden block and bullet
Replies
5
Views
2K
What is the force imparted by the bullet on the block
Replies
8
Views
4K
Momentum problem -- Two bullets fired into a block
Replies
7
Views
2K

Hot Threads

Recent Insights

Back
Top