How to deal with fluctuating input voltage?

  • Thread starter Thread starter naiht
  • Start date Start date
  • Tags Tags
    Input Voltage
AI Thread Summary
To manage fluctuating input voltage from a car engine's power supply, a reliable regulation method is necessary, as the voltage varies between 10-14V. A Zener diode is not suitable since its breakdown voltage must be below 10V, failing to meet the 12V requirement. Instead, a buck-boost converter or a voltage regulator that can handle both stepping down and stepping up the voltage is recommended for efficiency. While linear regulators can only reduce voltage, more complex circuits with capacitors and inductors are needed for broader regulation capabilities. The discussion emphasizes the importance of selecting the right regulator based on current consumption and specific project needs.
naiht
Messages
3
Reaction score
0
I am doing a tacho-meter of a single 12V power supply, it is meant for a car engine.
However in real life the power supply from an real vehicle fluctuates between 10-14V.

In this situation it is clear that some form of power supply regulation is needed.

I am currently considering a Zener diode (zener regulation); but if so the breakdown voltage (or the zener value) has to be lower than 10V, which does not meet the 12V supply requirement.

Are there any more suitable power supply regulation that can deal with the fluctuation?
Say, make 10V to 12V and make 14V to 12V?

Hope you understand my questions!
Thanks all!
 
Engineering news on Phys.org
What you want to do is run off a voltage less than what your lower limit is going to be... say 5V and then get a voltage regulator to handle getting you the 5Vs from your varying range of input voltages.

Just do a google search for voltage regulator and find one that fits your needs.
 
You can use
http://en.wikipedia.org/wiki/Buck–boost_converter
type circuit.
There are integrated circuits for this sort of regulator. It is also highly efficient (more efficient than resistor+zener).
 
I appreciate your replies!

Dmytry, if efficiency is not concerned, will this one http://ecelab.com/circuit-regulator-opamp.htm work?
I am not really familiar with converters and the circuit looks complicated with those RLC...

I am trying to do comparisons to find the most suitable way for my project :)
 
Oh and one more thing, the regulator's circuits have +ve & -ve terminal, while I only need a single +12V voltage supply... How should I connect the regulator?
 
naiht said:
I appreciate your replies!

Dmytry, if efficiency is not concerned, will this one http://ecelab.com/circuit-regulator-opamp.htm work?
I am not really familiar with converters and the circuit looks complicated with those RLC...

I am trying to do comparisons to find the most suitable way for my project :)
The circuit you linked can only step down the voltage I'm afraid. It's a linear regulator, dropping the voltage on the transistor.
What is the current consumption?
For the regulation that can step it up as well as down, you absolutely need complicated-looking circuit with energy storing elements (capacitors, inductances). It is not necessarily complicated to build through.
One example.
http://cache.national.com/rd/PAhtml/PADC_NSC0102.html

edit: another example specifically for your situation:
http://www.maxim-ic.com/app-notes/index.mvp/id/411
 
Last edited by a moderator:
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Back
Top