How to Calculate the Fatigue Limit of Leaf Springs?

AI Thread Summary
To calculate the fatigue limit of leaf springs, one must use stress equations specific to leaf springs to determine the stress values. These stress values can then be applied to the S-N curve relevant to the material being used. There is no shortcut; a thorough understanding of material properties and stress analysis is essential. The process involves correlating cycles to failure with the derived stress values. Accurate calculations are crucial for ensuring the durability and performance of leaf springs.
fpdlskf
Messages
7
Reaction score
0
Hi to all.

How would I go about calculating the fatigue limit of leaf springs?

Is there an equation out there in the form of

N, cycles to failure= f(variables, material properties)


Or will I have to use the Stress equations for leaf springs and use that stress value and
then look up a S-N curve for that particular material??


Tnx in advance.
 
Engineering news on Phys.org
There are no shortcuts in this life. You will have to use the stress equations for the springs and then use those stresses in the S-N curve for the material. That's what you'll be getting the big bucks to do!
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'What type of toilet do I have?'

Thread 'What type of toilet do I have?'

I was enrolled in an online plumbing course at Stratford University. My plumbing textbook lists four types of residential toilets: 1# upflush toilets 2# pressure assisted toilets 3# gravity-fed, rim jet toilets and 4# gravity-fed, siphon-jet toilets. I know my toilet is not an upflush toilet because my toilet is not below the sewage line, and my toilet does not have a grinder and a pump next to it to propel waste upwards. I am about 99% sure that my toilet is not a pressure assisted...
View full post »

Thread 'Thread No-Go plug gage allows 3 turns to enter. That's too many!'

After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
View full post »

Similar threads

How Can We Calculate the Fatigue Life of a Simply-Supported Beam?
Replies
6
Views
3K
Fatigue life hand calculations based on static FEA results
Replies
4
Views
2K
How to tell if a spring is fatigue, creep or degrade?
Replies
5
Views
4K
Leaf Spring Deflection: Calculating Force & Displacement
Replies
4
Views
5K
Fatigue Testing: Calculating ΔK vs da/dN from R & Max Stress
Replies
1
Views
1K
A What is the fatigue limit for copper pipe with a factor of safety of 5?
Replies
2
Views
1K
Variable pitch spring calculations
Replies
1
Views
2K
How can I properly add plies to a composite leaf spring in ANSYS APDL?
Replies
3
Views
2K
Doubt on Fatigue Strength S-N diagrams
Replies
1
Views
2K
Fatigue analysis in the frequency domain
Replies
1
Views
1K

Hot Threads

Recent Insights

Back
Top