EE senior electives - need advice

AI Thread Summary
The discussion revolves around selecting senior electives for an undergraduate electrical engineering degree, with a focus on areas like Electromagnetics, Controls and Robotics, Power Engineering, Circuit Design, Microprocessors, and Nanotechnology. The participant is particularly interested in Control Theory and Nanotech, seeking insights into job market demand and growth potential in these fields. Recommendations highlight the promising future of nanotechnology and the established nature of VLSI design, suggesting that both areas could offer valuable career opportunities. Additionally, the participant is open to taking more than the required three electives if their schedule allows. Overall, the conversation emphasizes the importance of choosing electives that align with both personal interests and market trends.
ionlylooklazy
Messages
30
Reaction score
0
dont know if this is the right forum, but...

For my undergraduate degree I have to take three senior electives of my choice. There are 38 courses in 13 concentration areas, but I only have interest in a handful;

-------------------------------------------------------------

Electromagnetics

- Antennas
- Electromagnetics I


Controls and Robotics

- Control Theory I
- Control Theory II
- Mechanics and Control of Robotic Manipulators


Power Engineering

- Introduction to Power I
- Introduction to Power II
- Introduction to Power III


Circuit Design

- Micro and Nano Electronics Device Fabrication
- NanoElectronics & NanoTechnology (my uni is still experimenting with this class)
- VHDL Design
- VLSI Design I
- VLSI Design II


Microprocessors

- Microcomputers
- Advanced Microprocessors
- Intelligent Robotics (more of a hobby class, competes in RoboCup (robotic soccer))


Electronics

- Physical Electronics
- Advanced Analog Circuits
- Advanced Digital Circuits


Industrial Controls

- Introduction to Programmable Logic Controllers (PLC)


the remaining areas are:
Optoelectronics and Photonics
Communications
Digital Systems
Global Engineering
CpE Related Courses

Avionics Engineering (big avionics program at my uni)
----------------------------------------------------------------


I was wondering if anyone has any experience in any of these fields and if they could offer some insight.

also, I was curious as to what kind of demand these fields have in the work-place and which fields have a lot of growth potential (nanotech?)

right now, I am leaning more towards control (PLC, control theory I & II), but am just as interested in Nanotech and ElectroMagnetics

we are required to take three, but can take more if we can fit it into our schedule (they count towards tech electives too!)

any advice/information is appreciated

much thanks
ionlylooklazy
 
Last edited:
Engineering news on Phys.org
My recommendation is nanotechnology. It's new (Exciting) and will start growing like a weed. You will be one of the pioneers. VLSI stuff is also good, but you will need to work hard to come up to speed. The industry is now well established.
Good luck.
Joe
 
is there anyone here that has any experience in the nanotech field or know where I can found out general information in regard to electrical engineering?
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
Thread 'Electromagnet magnetic field issue'
Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...

Similar threads

Replies
18
Views
2K
Replies
4
Views
2K
Replies
3
Views
2K
Replies
4
Views
1K
Replies
7
Views
3K
Replies
7
Views
2K
Back
Top