Recent content by cd80187

  1. C

    Breakdown Potential in a cylinder

    I set it up as 10 kV/mm = x/180mm. And the length of the cylinder is 18cm, the thickness is .34 cm.
  2. C

    Breakdown Potential in a cylinder

    What formula should I be using for this then? I tried just using a simple proportion, but it didn't work out
  3. C

    Breakdown Potential in a cylinder

    You are asked to construct a capacitor having a capacitance near 1 nF and a breakdown potential in excess of 9000 V. You think of using the sides of a tall plastic drinking glass as a dielectric (with a dielectric constant 5.0 and dielectric strength 10 kV/mm), lining the inside and outside...
  4. C

    Can a Plastic Drinking Glass Handle Over 9000 V as a Capacitor Dielectric?

    You are asked to construct a capacitor having a capacitance near 1 nF and a breakdown potential in excess of 9000 V. You think of using the sides of a tall plastic drinking glass as a dielectric (with a dielectric constant 5.0 and dielectric strength 10 kV/mm), lining the inside and outside...
  5. C

    Dynamics, plane drops mass trajectory question

    Homework Statement The pilot of an airplane, carrying a package of mail, wishes to hit recovery location A. Assume that the plane is traveling at constant speed of 200 km/hr at a constant height of 100m above the ground. What angle theta with the horizontal should the pilot's line of sight...
  6. C

    Electric Field due to Line of Charge

    OK, I'm not sure about this, but shouldn't everything cancel out, except for the one line that is perpindicular to the x axis? (aka the y-axis line). So then could I just use a point charge equation of (1/ 4pi x permitivity constant) x (q/r squared). But I have no clue how to integrate it, or...
  7. C

    Electric Field due to Line of Charge

    In Fig. 22-41, two curved plastic rods, one of charge +q and the other of charge -q, form a circle of radius R = 3.28 cm in an xy plane. The x-axis passes through both of the connecting points, and the charge is distributed uniformly on both rods. If q = 11.8 pC, what is the magnitude of the...
  8. C

    Finding the Support and Ratio of Mass for a Horizontal Lead Brick on Cylinders

    In Fig. 12-49, a lead brick rests horizontally on cylinders A and B. The areas of the top faces of the cylinders are related by AA = 2.4 AB; the Young's moduli of the cylinders are related by EA = 2.2 EB. The cylinders had identical lengths before the brick was placed on them. What fraction of...
  9. C

    Optimizing Automobile Suspension: Calculating Spring and Damping Constants

    I was able to solve the first part, but I could not get the second part. The book gives us two equations, and I think I am supposed to use this one : omega (w) = Square root of (k/m - b squared/4msquared). But beyond that, I am unsure what I am supposed to do
  10. C

    Optimizing Pendulum Period with Center of Mass Distance

    Yeah, I got the question right, I realized that I was forgetting to cancel out the square root. Thank you for the help
  11. C

    Calculating Amplitude and Initial Values in Simple Harmonic Oscillator

    A simple harmonic oscillator consists of a block of mass 2.60 kg attached to a spring of spring constant 380 N/m. When t = 2.30 s, the position and velocity of the block are x = 0.148 m and v = 4.080 m/s. (a) What is the amplitude of the oscillations? What were the (b) position and (c) velocity...
  12. C

    Optimizing Pendulum Period with Center of Mass Distance

    In Fig. 15-46, a stick of length L = 1.8 m oscillates as a physical pendulum. (a) What value of distance x between the stick's center of mass and its pivot point O gives the least period? (b) What is that least period? For this problem, I wasn't sure where to start, I would have thought that...
  13. C

    Optimizing Automobile Suspension: Calculating Spring and Damping Constants

    The suspension system of a 1700 kg automobile "sags" 13 cm when the chassis is placed on it. Also, the oscillation amplitude decreases by 43% each cycle. Estimate the values of (a) the spring constant k and (b) the damping constant b for the spring and shock absorber system of one wheel...
  14. C

    Calculating Rotational Velocity and Force on a Loop-the-Loop Track

    But just to ensure, I find v using the m x g = m(v squared)/ R, and then using that, I will use the equation m x g x h = (m g h) + .5 m (v squared) + (.5 (I)(v/r)squared? And I = m (rsquared), correct?
Back
Top