Concerning Elastic collisions and Kinetic energy

AI Thread Summary
The discussion focuses on an elastic collision between two balls of different masses, where the initial kinetic energy is questioned. The expected answer for the minimum kinetic energy of the system is (2mVo²)/3, despite the belief that kinetic energy remains constant throughout the collision. It is clarified that while total kinetic energy is conserved overall, during the collision some energy is temporarily converted into potential energy due to deformation. The momentum before and after the collision is conserved, leading to a common velocity of (2/3)Vo for both balls at a certain point. The conversation also touches on study resources for better understanding, particularly for students preparing for IIT.
neeraj93
Messages
10
Reaction score
0

Homework Statement


A ball of mass 2m is moving with a velocity Vo collides elastically and head-on with another ball of mass m at rest.
Find the minimum kinetic energy of the system.


Homework Equations


K = 1/2 mv2


The Attempt at a Solution


I personally do not understand what is expected of me here. The answer expected is
(2mVo2)/3.
But collision is elastic. And I have to find the Kinetic energy of the system. Won't the Kinetic energy of the system remain constant (mVo2) throughout?
 
Physics news on Phys.org
Yes, it should be constant. I suspect the question meant something else, or the answer is wrong.
 
Yes, the kinetic energy remains constant, but a more close look tells you that, the 'initial' and 'final' kinetic energies are same, i.e. during a collision (for the split second when they are in contact), the kinetic energy is not conserved. The reason is as follows:

Consider a spring attached to the body initially at rest.
During collision, the spring is deformed, and at the same time, the body at rest gains speed, while the body which was moving initially is slowed down, also the spring gets compressed.
Now, a time will come, when both the bodies will travel with same velocity, and the compression in the spring would be max. or the energy stored in the spring will be max. Later on, the body with spring will gain much more speed than the other and speed away.

So, you can see that some part of the kinetic energy was stored in the spring as its potential energy. But, later it again converted to their kinetic energies.

Similarly, in bodies, there's some deformation (similar to spring, although for a short while), and as a result, some potential energy is gained(at the cost of kinetic energy).
Momentum can be conserved anytime, as the spring(or contact) force acts on both the bodies equally in opposite directions, and as a system, there's no external force.
For your answer,
Initial momentum = 2mv0
Final mometum(when they are traveling with common velocities (vc))
= 3mvc

So, vc = (2/3)vo

KE of system (sum of KEs of two mases) = (2/3)mvo2

Since you are an Indian (so am I)...I suggest you read up HC Verma part 1 Pg. 145 for better understanding...good luck...btw, u in 11th now, preparing for IIT, right?

Well, I am in 12th now, giving IIT this year...
 
Oh, It isn't there in Resnick, so no wonder. I, personally, don't prefer using Verma.. I'll have a look, but. thanks.
I'm in 12th too, btw.
 
oh...ok...all the best for your boards n all !
 
Thanks, good luck to you too!
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top