Is the Transmitter Circuit Drawn Correctly?

  • Thread starter diegovishnu
  • Start date
  • Tags Tags
    Circuit
9 replies · 5K views · last reply
diegovishnu
Messages
5
Reaction score
0
i am trying to do the circuit "www.electronicsforu.com/efylinux/circuit/.../aug99_IRcordless.pdf"[/URL]
the phototransistor showed in the circuit has only 2 leads but the 1 i brought has 3 leads with a number 1838 written on the top..
please help me what to do. even if i brought a new 2 lead phototransistor, how to find the emitter and collector?

also please help me with the audio output transformer. I am not getting it anywhere in the shops
 
Last edited by a moderator:


That link doesn't seem to work.

However the device you have may be a TSOP1838
Here is a data sheet for it:

http://pdf1.alldatasheet.net/datasheet-pdf/view/26604/VISHAY/TSOP1838.html

If it is that one, it needs a pulsed signal at 38 KHz to work. Almost any domestic remote control should give some results with it.

That data sheet does not give the pin connections, but the following image is better.

Diagram of a TSOP 1838 infrared receiver: a brown rectangular package with a purple dome lens and three legs labelled 1=Vcc, 2=GND, 3=Out.
 


No, if this device you have is the TSOP1838, then you can't really use it as an optical audio receiver. They are meant for remote controls.

If possible, take it back and exchange it for a proper photo-transistor.

Be careful also not to get a light dependent resistor. These are Cadmium Sulfide cells and have a very poor frequency response.
 


i brought 1 phototransistor.but its not semicylindrical as the circuit say..its a blue 1 which looks similar to an LED.
you told the circuit may not work. can you clarify on that?
thankyou in advance
 


diegovishnu said:
it will not work?

No, your first link did not work. Next, No, the part you bought is an integrated circuit not a "straight" IR photo transistor. The part you bought includes a circuit to make it easy to use as an IR detector for a remote control, which uses a pulsed IR signal, and decodes it. (Changes the pulsed signal to data bits).

You will need a different part like:

http://www.fairchildsemi.com/ds/QS/QSC112.pdf

Fish
 


thankyou...

if the link will not work (but the ckt is one whch came on e4u magazine!) i'll be glad if you could refer some similar circuit..
 


If it looks like a LED, then it might be OK. Remote control receivers usually look like the picture above, that is fairly flat with a window on one side.

Try testing it as a transistor but with the top of the device covered over to stop light getting in.
A digital multimeter will usually be able to test transistors in the Hfe setting.

If it tests OK as a transistor, disconnect the base connection and expose the device to light and see if you get a variation in meter reading.


if the link will not work (but the ckt is one whch came on e4u magazine!) i'll be glad if you could refer some similar circuit..
"the link will not work" means that if we click on the link we get no picture, not that the circuit in the link won't work.
 


Circuit schematic titled FIG.2: IR Audio Receiver, showing an IR phototransistor T3 feeding transistor stages T4 and T5 (BC549C), a volume pot VR2 100K, and output transistor T6 (BEL187) driving a headset, powered by a 9V battery with ON/OFF switch S1.


this is the reciever circuit.
and here is the transmitter
Circuit schematic of an IR audio transmitter: headphone socket audio input from TV feeds an audio output transformer X1 connected in reverse, with VR1 10K, R1 4.7K and R2 22K biasing transistor T1 BC547, R3 100 ohm, red LED, C1 220 uF 16V, T2 BD140/SK100, R4 10 ohm 1W, and IR LED1 and IR LED2 to +9V.
 


diegovishnu said:
Schematic of an IR audio receiver with an IR phototransistor input, transistors T4 and T5 (BC549C), a BEL187 output transistor T6 driving a headset, a VR2 100K potentiometer, and a 9V battery with an on/off switch S1.


this is the reciever circuit.
and here is the transmitter
Schematic of an IR audio transmitter: headphone-socket audio input from a TV feeds a transformer X1 wired in reverse, with VR1 10K, R1 4.7K and R2 22K biasing transistor T1 (BC547), which drives T2 (BD140/SK100) and two IR LEDs, with a 220uF 16V capacitor and red LED on a 9V supply.

In the transmitter circuit, T1 base appears to fed with a relatively large audio signal without any added DC bias. I believe that this is likely to give a grossly distorted result - are you certain that this has been drawn correctly?