Transfer characteristics of a diode circuit

10 replies · 2K views · last reply
Bling Fizikst
Messages
119
Reaction score
16
Homework Statement
refer to images
Relevant Equations
refer to images
Circuit schematic with input v1+ on the left and output v2+ on the right, a 1 kΩ resistor R in series on the top rail, and a 2 V battery in series with a diode to ground at the midpoint.





Circuit schematic of a diode clamper-and-peak-detector: source v = Vm sin wt in series with capacitor C1, node V1 with diode D1 to ground, diode D2 in series to node V2, capacitor C2 to ground, and load RL in parallel with C2. Problem text reads: For the given circuit, plot V1 and V2. Assume RLC2 > 100T.

What do i need to do for transfer characteristics for the first problem (B)?
I plotted the ##V_1## and ##V_2## plot on the same graph:
Hand-drawn graph of V1 (black) and V2 (purple) against t on shared axes, with V1 sinusoid peaking near 10 and V2 clipped flat at 2 on the positive side and following V1 on the negative side, marked -10 and 0.

Is it correct?

For the second problem , i guess the capacitor ##C_1## is just there to ensure AC flow .
But really unsure how to approach this .
 
Bling Fizikst said:
Is it correct?
Can you explain your reasoning ?

##\ ##
 
BvU said:
Can you explain your reasoning ?

##\ ##
As long as the potential at the p type end is less than ##2## , it is reverse biased . This means the output volatge is the same as input voltage . Hence , it over laps with ##V_1## till it hits ##2## . When the potential is ##2## at the p type end , then diode is forward biased again and the output voltage is also ##2## as long as it is ##2## or more . Since the input is alternating , this means the potential will again drop below ##2## and the ouptut voltage will be the same as input voltage
 
Bling Fizikst said:
As long as the potential at the p type end is less than ##2## , it is reverse biased .
How come I get the idea that it's not 'less than +2 V' , but 'more than -2 V' ?

##\ ##
 
I am sorry , the graph i sent earlier is compltetly wrong . Here is my newer attempt :

Handwritten diode clipping circuit with input Vi, series resistor R, a 2 V battery and ideal diode to a -Vm reference, with a sketch of the output Vo against time beside it, clipped at -2 - Vm, and two case conditions written below.
 
Is it necessary to bring a new actor on the stage ? What is ##V_m## ?

Be sure to scale the ##V## and ##t## axes (in order not to risk losing points)...
For the same reason, don't forget parts B) and C) ...

Bling Fizikst said:
For the second problem , i guess the capacitor ##C_1## is just there to ensure AC flow .
There is no info on the value of ##C_1##. What if it is huge? What if it is really small ?
Compare with the role of the 2V battery in exercise 4)

Bling Fizikst said:
But really unsure how to approach this .
You can start by distinguishing ##v_m\sin(\omega t) > 0## and ##<0##

##\ ##


##\ ##
 
I am struggling in the positive half cycle case :
I get ##V_1=V_2## as ##D_1## is reversed biased and ##D_2## is forward biased so it is shorted .
Now , i end with a circuit with ##C_1,C_2## in series and AC source ##V## .
How do i find ##V_2##?

For the negative half cycle case:
##D_1## is forward biased so all the current flow through it . Hence , ##V_2=0## and ##V_1=V##
 
Bling Fizikst said:
I am struggling in the positive half cycle case :
I get ##V_1=V_2## as ##D_1## is reversed biased and ##D_2## is forward biased so it is shorted .
Now , i end with a circuit with ##C_1,C_2## in series and AC source ##V## .
How do i find ##V_2##?

For the negative half cycle case:
##D_1## is forward biased so all the current flow through it . Hence , ##V_2=0## and ##V_1=V##
Seems to me you also struggle with the negative half cycle case :wink:
(Just so you know: I'm not trying to insult and I don't have all the answers; -- just trying to help as best I can!)

Here's a few remarks:

I don't understand your 'Hence ##V_2=0## and ##V_1=V##' . You are given that ##R_L C_2 > 100 T##, so, once ##C_2## is charged, ##V_2## only drops less than one percent during a cycle !

Without ##C_1## and ##D_1## the circuit is a half-wave rectifier. Maybe it's a good idea to google that and study its working (if you aren't already familiar with the subject).

The left part of the circuit (voltage source, ##C_1## and ##D_1##):
I agree with you that 'For the negative half cycle case: ##D_1## is forward biased'
So if ##C_1## isn't charged already, it will be charged up to a maximum of ... ?

And with the remainder of the circuit in place: at the same time (i.e. during a negative half cycle), ##D_2## is forward biased -- under the condition that ##v_1 > v_2##

What do you think ?

[edit] ready to continue with the positive half-cycle once you are back and have filled in the ...

##\ ##
 
Last edited:
Bling Fizikst said:
I am struggling in the positive half cycle case :
I get ##V_1=V_2## as ##D_1## is reversed biased and ##D_2## is forward biased so it is shorted .
Now , i end with a circuit with ##C_1,C_2## in series and AC source ##V## .
How do i find ##V_2##?

For the negative half cycle case:
##D_1## is forward biased so all the current flow through it . Hence , ##V_2=0## and ##V_1=V##
Lost interest?
 
BvU said:
[edit] ready to continue with the positive half-cycle
Never happened, but (for posterity):

the circuit is a voltage doubler. See here or here

##\ ##