Adding stirring force acting on the fluid

In summary, when stirring fluid in a beaker, the motion of the fluid is calculated using smoothed particle hydrodynamics lagrangian method. However, adding stirring motion results in collision detection rather than actual fluid dragging. To properly model this, one should use continuum fluid dynamics and treat the fluid as a viscous Newtonian fluid. This involves solving the Navier Stokes equations and calculating the stress tensor at the stirrer surface. It may be possible to approximate the force using existing solutions for flow past an infinite cylinder and the drag coefficient as a function of Reynolds number. Alternatively, existing force data on fluid stirring can be used as a reference.
  • #1
muffinman123
19
0
when you stir fluid in a beaker of fluid, how is the motion on the fluid by the stirring rod calculated?

the fluid is represented using smoothed particle hydrodynamics lagrangian method so that I can look at fluid as a bunch of spheres interacting with each other through a sort of force field.

so now I try to add stirring motion into this, and so far I only have collision detection implemented using penalty force, and the results do not reflect the stirring motion because the fluid particles do not get dragged by the stick at all.

how should the stirrind rod transfer its motion into the pool of spheres and drag the fluid with it?
 
Physics news on Phys.org
  • #2
muffinman123 said:
when you stir fluid in a beaker of fluid, how is the motion on the fluid by the stirring rod calculated?

the fluid is represented using smoothed particle hydrodynamics lagrangian method so that I can look at fluid as a bunch of spheres interacting with each other through a sort of force field.

so now I try to add stirring motion into this, and so far I only have collision detection implemented using penalty force, and the results do not reflect the stirring motion because the fluid particles do not get dragged by the stick at all.

how should the stirrind rod transfer its motion into the pool of spheres and drag the fluid with it?

This is not the way to model the fluid mechanics of a stirring rod in a fluid. You should be using continuum fluid dynamics, and treating the material as a Newtonian fluid (viscous fluid). The boundary condition with any solid is zero velocity difference at the boundary (the so-called non-slip boundary condition). This is a routine problem for computational fluid dynamics software. The equations solved are the Navier Stokes equations.
 
  • #3
can you link me to the procedure to approach this problem? I realized too that this must be solved in the Navier Stokes equation, not just simple collision detection like walls and stuff, but I don't know how the forces work in that perspective since I am pretty new to fluid mechanics myself. thx
 
Last edited:
  • #4
To get some good background on fluid mechanics, see Transport Phenomena by Bird, Stewart, and Lightfoot. This is not an elementary problem to solve. The computational fluid dynamics people first started getting solutions to problems like this (and ones with more complicated industrial stirrers) only about 20-30 years ago. You have a moving boundary, which is always hard to handle. You are interested in getting the load on the stirrer. They calculate that. All the detailed mathematics is done by the software, using the finite element method. One of the things it calculates (among many) is the stress tensor at the stirrer surface. It then properly integrates the stresses to get the load. I suggest you google computational fluid dynamics software if you are really serious about doing this problem. There may also be articles in the literature by people who have already solved similar problems. I'm sure that the CFD software vendors would be happy to accommodate you, but it probably won't be cheap.
 
  • #5
thing is, I already have SPH program, is there no reasonable way to add the effects of the stirring force into my numerical solution?

my lagrangian navier stokes equation is already much simplified. the momentum equation has 3 terms, pressure, viscosity, and external force.

surely there must be a way to describe the force the stirring rod applies to the fluid at that location in that velocity and acceleration.
 
Last edited:
  • #6
To get a first approximation to the force, you might consider the solutions available for flow past an infinite cylinder. This is the same as the solution for movement (at constant speed) of a cylinder through a stationary fluid. The drag force on a cylinder is presented in the literature in terms of the drag coefficient as a function of the Reynolds number. Google drag on a cylinder.
 
  • #7
just wondering, is there any place where I can find existing force data on fluid stirring? I have a force sensor but it won't register anything under a Newton. stirring water won't even beat the noise values, so I am hoping there are existing data I can use as reference
 

FAQ: Adding stirring force acting on the fluid

1. What is stirring force?

The stirring force is a force that is applied to a fluid in order to mix or stir it. This force can be created by using a stirring rod, a mechanical stirrer, or any other device that can agitate the fluid.

2. How does adding stirring force affect a fluid?

Adding stirring force to a fluid increases the kinetic energy of the fluid particles, causing them to move and mix more quickly. This can help to blend different components of the fluid together or break up any clumps or particles that may have formed.

3. What are the benefits of adding stirring force to a fluid?

The benefits of adding stirring force to a fluid include promoting even distribution of components, preventing settling or separation of particles, and increasing the rate of chemical reactions or heat transfer within the fluid. It can also help to remove any air bubbles or impurities from the fluid.

4. What factors affect the amount of stirring force needed for a fluid?

The amount of stirring force needed for a fluid depends on various factors such as the viscosity of the fluid, the size and density of the particles or components in the fluid, and the desired level of mixing or agitation. The shape and speed of the stirring device can also play a role in the amount of force needed.

5. Can too much stirring force be harmful to a fluid?

Yes, excessive stirring force can sometimes cause damage to a fluid, especially if the fluid is delicate or easily affected by external forces. It can also lead to excessive foaming, splashing, or spills. It is important to carefully consider the properties of the fluid and adjust the stirring force accordingly to avoid any negative effects.

Similar threads

Replies
1
Views
1K
Replies
9
Views
11K
Replies
34
Views
10K
Replies
2
Views
2K
Replies
2
Views
4K
Back
Top