Yes. The coil uses 675m of #18 copper wire. 3 sets of 5 (total 15) very powerful N50 Neodymium magnets. One set is 5@18,800 Gauss each & having 650 lbs of pull force each Total 94,000 Gauss=9.4T A second set is 5 @13,300 Gauss and 210lbs of pull force each Total 66,500Gauss =6.7T A third set of...
Whats the easiest way to test the max output of electricity induced in an air coil.
I will wire it 3 phase delta. (or double delta) Will I need a resistive load attached for current flow? What should I use? How do I test? Use a multi tester? Is there math I can use to estimate the amount. I...
I'm winding copper wire around a hollow plastic toroidal to make a coil. I am moving 3 magnetic fields proximate to the copper wire coil. I want to get the most current possible from the coil Should I wind the wire as one single wire layered several times? Should I wrap each layer the opposite...
Magnetic Induction in a copper wire toroidal
Thanks Berkeman for your response. I appreciate the input.
The things that make magnetic induction more efficient are
A) amount of copper wire
B) the speed at which you change the magnetic field
C) the strength of the magnetic field
Do you...
Ive made an experimental generator built loosely of the Faraday flashlight technology. Rather than a linear air coil using a reciprocating magnet I've made a toroidal coil and added magnets on the outside of the toroidal to coerce unidirectional movement of the interior magnets that match the...
Thanks for you response. It was the perfect solution.
What I'm trying to do: A trigger magnet affixed to the periphery of a rotating shaft, passes the trigger magnet under a fixed reed switch. It switches a current supply on. 140 degrees of rotation later, I have a second trigger magnet to...
Its just an on/off thing. What I'm trying to do:When a magnet affixed to a rotating shaft passes the reader, it switches the current on. 140 degrees of rotation later I want a second magnet to turn it off. I need a GTO type SCR. Problem is so far is that... To turn on you send a + tive signal to...
If I'm using a weak signal like from a tiny magnetic reader, how do I get it to trigger a 120 volt coil?. What electronic hardware do I need to wire in between? Or what type of switch can do this? Thanks.
What is the best material to use for the bobbin (spool) to wind the copper wire around. I know plastic is used, but is aluminum any good for this? How do you determine which direction the rod will tavel through the coil without testing it first?
Hey, anybody out there good with electrical stuff??
I'm no genius but can I be correct in assuming the following?
Im making high voltage electromagnets.
If I use 1200 winds of awg30 magnet wire, it will have the same power ~ (EMF) Or (magnetic field strenghth) as 600 winds of awg15 magnet...
The primary wave has a spike @ 88*deg. starting at .009 and the secondary wave ending at .012 it peaks at 730 The electro magnet is a sine wave of unknow feq. I am not a pro at this. what numbers do you need to determine B?
The copper coil has 35,000v current running throught it. This current is distributed to each electromagnet intermittantly. It is wound around an iron core. The iron core becomes an electromagnet. A field of magnetic energy runs alog its axis out the ends creating a north and south pole. It...
Well actually they are changeable but not as easily as adding or subtracting windings. The number of windings can go up quite a bit, there's plenty of room for it. The equation I am using asks for B over 2 to be multiplyed all the brackets off work done previously. Whats B ? Heres what I've...
Ive designed an electromagnetic piston engine. I am affixing electromagnets concentrically to the cylinder bore of a 4 cylinder automobile engine. The pistons inside the cilynders are modified with a perminant magnetic N42 face. Polarity is +. The electromagnets are made of iron 1018 and act as...