Buy Cable Strain Relief | Mouser, Amazon & Beyond

  • Thread starter Thread starter Jiggy-Ninja
  • Start date Start date
  • Tags Tags
    Cable Strain
AI Thread Summary
Strain reliefs are difficult to find, especially on platforms like Amazon, which mostly offer RJ-45 booties. Users express frustration with Mouser, noting that it's challenging to navigate without specific product knowledge. A preference for larger, flexible strain relief options, similar to those used on LeCroy Differential Probes, is mentioned. Heat shrink tubing is also highlighted as a preferred solution for strain relief. The discussion emphasizes the need for better sourcing options for specific strain relief products.
Jiggy-Ninja
Messages
309
Reaction score
1
Where can I buy strain reliefs? All I could find on Amazon are 6,000 different kinds of RJ-45 booties, which are not what I'm looking for. Mouser is impossible for things like this unless you already know exactly what you are looking for.

I quite like the strain relief used on the LeCroy Differential Probes (picture attached for reference) that we have at work, and would like something big and flexible like that if possible.
 

Attachments

  • Lecroy Strain Relief.JPG
    Lecroy Strain Relief.JPG
    46.6 KB · Views: 460
Engineering news on Phys.org
I like using heat shrink tubing. Works for me.
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Job Skills Got my BS in Physics but I don't know what to apply for
3
Replies
108
Views
18K
Focus all of your ire on me, if you would
Replies
4
Views
2K
B Which probability calculation is "more correct" in Baccarat games?
Replies
9
Views
4K
I am VERY interested in Electrical Engineering where do I start?
Replies
25
Views
22K
I About non-observable assumptions
Replies
28
Views
3K
Neuroscience MS considering switch to EE. Help?
Replies
1
Views
2K
I 'Formulations' of Physical Theories: Overview?
Replies
2
Views
14K
I The world from a bat's perspective (sonic images)
Replies
21
Views
2K
I A Bold New Take on Quantum Theory
Replies
25
Views
5K
I Interpretation of QM in the Heisenberg Picture
Replies
34
Views
5K

Hot Threads

Recent Insights

Back
Top