Difution drift currect question

  • Thread starter Thread starter nhrock3
  • Start date Start date
  • Tags Tags
    Drift
AI Thread Summary
The equation J_e=qμnE-qD_e(dn/dx) describes the drift and diffusion current of electrons in a semiconductor. In this equation, J_e represents the electron current density, q is the charge of an electron, μ is the drift coefficient, n is the electron density, E is the electric field, D_e is the diffusion coefficient of electrons, and dn/dx is the spatial derivative of electron density. The term dn/dx indicates how electron density varies with position, leading to diffusion from high to low concentration areas. Additionally, the formula for hole current differs by having a positive sign due to the positive charge of holes compared to the negative charge of electrons. Understanding these components is crucial for analyzing semiconductor behavior.
nhrock3
Messages
403
Reaction score
0
J_e=q\mu \bar{n}E-qD_e\frac{d\bar{n}}{dx}
i can't understand this equation
what each member of this equation

i only know that \mu is the drift coefficient
E is the field

what the rest of the memebers represent
?
 
Engineering news on Phys.org
nhrock3 said:
J_e=q\mu \bar{n}E-qD_e\frac{d\bar{n}}{dx}
i can't understand this equation
what each member of this equation

i only know that \mu is the drift coefficient
E is the field

what the rest of the memebers represent
?

I googled diffusion drift current, and got lots of good hits. Here's one that should answer your question:

http://ecee.colorado.edu/~bart/book/book/chapter2/ch2_10.htm

.
 
n is the electron density what is the meening of
dn/dx
?

in this page it doesn't say what is D_e
?

the is also a formula for hole current
why it has plus in the middle (in the electron current we have minus in the meedle)
??
 
nhrock3 said:
n is the electron density what is the meening of
dn/dx
?

dn/dx would be the derivative of electron density with respect to the coordinate x. In other words, if you're simply dealing with a semiconductor in which the elctron density only changes in x (i.e. y, and z components are constant), there will be a diffusion current where electrons will diffuse from a higher concentration area to a lower concentration area. This is mathematically depicted by 'dn/dx'.

nhrock3 said:
in this page it doesn't say what is D_e
?

D_e (or D_n) is the diffusion coefficient of electrons. It depends on the mobility of the electrons, and temperature of the sample.

nhrock3 said:
the is also a formula for hole current
why it has plus in the middle (in the electron current we have minus in the meedle)
??

The hole current has a plus because holes are positively charged as opposed to electrons which are negatively charged
 
thanks :)
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top