Eletric motor with wind turbine (And in side small generator

AI Thread Summary
The discussion revolves around the concept of integrating wind turbines and small generators into electric vehicles to enhance energy regeneration. The proposal suggests using wind flowing over the car to power turbines that charge the vehicle's batteries, potentially generating around 65 kW of energy. However, participants highlight that this approach may not provide additional energy since the wind generated by the car's motion is already powered by the vehicle's batteries. The idea is criticized as resembling a perpetual motion machine, leading to the thread being locked due to forum rules. Overall, the feasibility of this energy solution remains highly questionable.
OnLy-_-1
Messages
2
Reaction score
0
Hello all my friends...! This is my first discusion about this type of discusion , so let make long short story i read people from 2009 want to find way how to use wind in car producion or self use... I was thinking let me try to find way to get solution on that problem so after long thinking , i find perfect way but now we will discuse its that in Practise usefull... i was thinking Electro motor 85kw (from tesla one Ac what consume 1000 amp 300 w) why its perfect on way with batery and motor can fit on L1 or (DN-One Project)... so Car Modification on Interior to be a bit up for 10 to 15 cm. So this type if turbines are not only air flow , they have Comlex Sistem what will control flow on air (to don't broke wind generators propeller) in side will have that kind of generators so that generators suply batery with energy + of roof solar I am thinking that will be on long way search on natural progress and own car regeneration on energy so if you ask me how much can produse energy ? I can say near 65kw with Both sistems so want to open discusion let talk so i want to hear opinions :) before i go in university to offer it

add my skype only-_-1
 
Engineering news on Phys.org
Welcome to PF;
It is unclear what problem you are trying to solve with this proposal.
There are already cars run on electric batteries and motors - including some which have solar panels ... what role would the wind turbine play in all this?

Is the idea to use the wind flowing over the car as it goes to run a turbine to charge the car's battery?
 
Simon Bridge said:
Welcome to PF;
It is unclear what problem you are trying to solve with this proposal.
There are already cars run on electric batteries and motors - including some which have solar panels ... what role would the wind turbine play in all this?

Is the idea to use the wind flowing over the car as it goes to run a turbine to charge the car's battery?
yes sorry for my bad unclear say... its wind flowing turbine inside have small generators for charge batery what they have each 16w (can be put 14 trubines in one car mesure : from 3 to 5 meter long and from1,80 to 2 wide) and max small generators can be put from 1700 to 1900
 
The wind to spin the turbines comes from the motor moving the car, which is powered by the batteries, so no new energy can be harvested this way.

Since this is an attempt at a perpetual motion machine, this thread is locked, per PF rules.
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Back
Top