I need to build an electromagnet to provide 10mN eddy current brake

AI Thread Summary
Anoop is developing a motor tester that requires a variable load using an eddy current brake with an electromagnet, aiming for over 10mNm load on a 75mm rotating disc at 6500 RPM. Initial attempts with a large rod core produced only 3mNm, while a dual electromagnet setup achieved 9mNm but faced space constraints. Suggestions include using a U-shaped magnet to optimize magnetic flux and experimenting with a C-clamp to adjust air gaps. Concerns were raised about heat generation from eddy currents affecting load consistency, and alternative methods for testing DC motors were discussed. The goal is to replace permanent magnets with electromagnets for smaller motors to allow configurable load profiles.
Anoop Varghese
Messages
3
Reaction score
0
Hi I am building a motor tester, for that I need to build a variable load. For which I was planning to use eddy current brake with electromagnet.

Please help me to build a electro magnet which can provide more than 10mNm load to a DC motor with rotating disc of 75mm in a RPM of 6500.

I tried with trial and error methods, as I am not good at solving mathematical expressions.
case 1. When I tried with a large rod core with 2100turns and 500mA current I was able to load only upto 3mNm. Case 2. when I change the system to two electromagent place at the both side of the disc (1400 turns each and 300mA cureent through both coil) I was able to load upto 9mNm. However as it need to be placed both side I have a space contrain.So please help me to build a electromagnet which can produce same loading as the case two in a smaller package.

Thanks & regards,
Anoop
 
Engineering news on Phys.org
What mathematical expressions are you trying to use?

It is not clear what you are trying to do.
 
case 1. When I tried with a large rod core with 2100turns and 500mA current
Can you post a photo of your experiment?
 
The magnetic flux should go in a circle with air gaps being as small as possible. A U shaped magnet could work.
 
  • Like
Likes Anoop Varghese
Dr Z is right.

My 2 cents(overpriced at that)
Experiment with a C-clamp (iron one of course)
gives you a magnetic loop with adjustable air gap.
Tighten clamp and tack weld that wobbly tip to the screw so it won't flop around.
upload_2015-7-17_12-33-52.png
 
Last edited:
  • Like
Likes Anoop Varghese
Anoop Varghese said:
I was planning to use eddy current brake with electromagnet.
As for a motor-tester I don't think it's a good idea: The rotating disc will be heated up by 680W Eddy current losses and will become hot - very hot.
The specific resistance of the disc will change due to change in temperature, so the load will not be constant.

Also the torque will depend on rotational speed.

Another idea for motor testing is to connect two (identical) motors mechanically, the one is used as motor, the other is used as generator. Then you let the generator provide power to the motor ( perpetual motion machine ). Of course that will not work, but if you insert some power supply in the electrical connection between generator and motor in series, adding some small voltage to the generator voltage, it will work. The power supply will just have to provide power, corresponding to losses in the motor/generator.

EDIT: Sorry, only 6.8W is lost in the rotating disc.
 
Last edited:
Hesch said:
As for a motor-tester I don't think it's a good idea: The rotating disc will be heated up by 680W Eddy current losses and will become hot - very hot.

108.3 rotations/second * 2 * π * 1m * 0.01N = 6.8W
 
Anoop Varghese said:
Hi I am building a motor tester, for that I need to build a variable load. For which I was planning to use eddy current brake with electromagnet.
So why not use a DC PM motor as a generator with a resistive load? That will give you eddy current braking.
If you load a DC generator, (motor), with a constant current network you will get close to constant torque over a wide range of RPM.
 
Baluncore said:
So why not use a DC PM motor as a generator with a resistive load? That will give you eddy current braking.
If you load a DC generator, (motor), with a constant current network you will get close to constant torque over a wide range of RPM.
The tester need to support 50 motors need to be tested together- it is used for the endurance testing
Baluncore said:
So why not use a DC PM motor as a generator with a resistive load? That will give you eddy current braking.
If you load a DC generator, (motor), with a constant current network you will get close to constant torque over a wide range of RPM.
And the user must be able to connect all their different type and sizes of motors in the system. So we thought of using the eddy current braking in the system with the disc and magnet. We have made the system with permanent magnet, however now customer need configurable load, so we are planning replace the permanent magnet with electromagnet.
 
  • #10
Anoop Varghese said:
The tester need to support 50 motors need to be tested together- it is used for the endurance testing
Which type of DC-motors: Mechanical/electronic commutation?

I have tested synchronous motors by driving them with a very poor commutation angle. Thus they were heated up while running, though they had no mechanical load, so that edurance due to heat and rotational wear were tested at the same time, but I'm not sure if the same can be done with a BLDC motor, which has trapezoidal commutation?
 
Last edited:
  • #11
Hesch said:
Which type of DC-motors: Mechanical/electronic commutation?

I have tested synchronous motors by driving them with a very poor commutation angle. Thus they were heated up while running, though they had no mechanical load, so that edurance due to heat and rotational wear were tested at the same time, but I'm not sure if the same can be done with a BLDC motor, which has trapezoidal commutation?
Hi Hesch,

Thanks for your suggestions, however we are testing normal DC motors. Not BLDC motors, the shaft and Disc is isolated with nylon bush so that the heat is not transferred to the motor from the disc.

For larger motors which is up to 1Nm torque we are using permanent magnet for loading. For smaller motor customer wants electromagent loading for simulating the load profile performance over the operational area.

Regards,
Anoop
 
Back
Top