Looking for help Retro Fitting a computer keyboard

AI Thread Summary
The discussion centers on retrofitting a computer keyboard inside an antique typewriter while preserving its aesthetic. The main challenge involves activating the typewriter keys to correspond with a modern keyboard's circuit board, with suggestions to use microcontrollers like Raspberry Pi or Arduino for better reliability. Participants highlight the need for soldering tools and basic programming skills to connect the systems effectively. Concerns about power issues and the complexity of building a new circuit are noted, emphasizing the importance of thorough planning and research. Overall, the project is deemed feasible with the right approach and resources.
vskjck
Messages
2
Reaction score
0
Long story short I want to Mount a Computer inside an Antique typewriter maintaining the look and feel of the antique. My initial plan is to dissasemble a Toshiba Satellite and disgard any thing I don't need (plastic housing, Maybe the speakers, and any chassis' I can do without) I have so far stripped the keyboard down to Flexible circuit board, and am looking for ideas on how to make the keys of the old typewriter activate the corresponding keys on the circuit board. This is The biggest problem I have with the project, I see it being very do able. underneath there are arms of metal that move about 3 -5 MM and I could make small contact swithces, very easily.What could I use to translate the contact switch to the digital keyboard that would be long lasting with minimal maintence? and where is the cheepest place to acquire such material, and what kinds of tools will I Need, I have basic tools, and can acquire specialty tools with in financial reason.
 

Attachments

  • IMAG1442.jpg
    IMAG1442.jpg
    40.7 KB · Views: 517
  • IMAG1441.jpg
    IMAG1441.jpg
    34.9 KB · Views: 489
Engineering news on Phys.org
Hi vskjck! http://img96.imageshack.us/img96/5725/red5e5etimes5e5e45e5e25.gif

vskjck said:
Long story short I want to Mount a Computer inside an Antique typewriter maintaining the look and feel of the antique.
A novel idea, certainly. But speaking as one who typed his thesis on a manual typewriter, can I suggest you re-consider the nostalgia for the "feel" of tender nails as the heavy keys push the nail away from your finger with sustained typing! :frown: Apart from the discomfort of bleeding nails, depressing heavy keys on a manual typewriter is a real drag on ones pace of typing.

I don't have suggestions, apart from think carefully before plunging in too deep. :smile: Time has not dimmed my memory of those frightful keyboards. https://www.physicsforums.com/images/icons/icon11.gif
 
Last edited by a moderator:
NascentOxygen said:
A novel idea, certainly.

Well, not really. :biggrin:

300px-Michael_Holley_Computer_1978_NWCN.jpg


The original Selectric mechanism was designed and manufactured by the office equipment division of IBM, and was not engineered for use as a computer terminal. Adapting this mechanism to the needs of computer input/output was nontrivial. Microswitches were added to the keyboard, solenoids were added to allow the computer to trigger the typing mechanism, and interface electronics were also needed.

http://en.wikipedia.org/wiki/IBM_Selectric_typewriter
 
all I want to do is basically extend the keyboard switches. each key has a simple I/O switch that is activated by completing a circuit. I would like to solder wires to both ends of the I/O swithch contacts and allow them to complete there actions in a remote location that is traversed via wire.

Can I do this?

my guess is that I am going to run into power issues.

i suppose another option would be to build an entire new circuit system, however interfacing that back to the computer and creating a driver to make the new circuit funtional is a bit beyond my abiility at this time.
 


I would suggest looking into using a microcontroller to translate the contact switches from the typewriter keys to the digital keyboard. This would allow for a more reliable and efficient connection between the keys and the circuit board. Additionally, you may want to consider using a Raspberry Pi or Arduino board to control the microcontroller and integrate it with the computer.

In terms of tools, you may need a soldering iron, wire cutters, and wire strippers to connect the microcontroller to the circuit board. You may also need some basic programming skills to program the microcontroller.

As for acquiring materials, I would suggest looking online for electronic components suppliers or visiting a local electronics store. It may also be helpful to reach out to online communities or forums for advice and recommendations on specific materials and tools.

Overall, it seems like your project is very doable with the right tools and materials. Just make sure to plan and research thoroughly before starting to ensure the best possible outcome. Good luck!
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Thread 'Electromagnet magnetic field issue'
Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...
Back
Top