Raman Effect and Fluorescence: Understanding the Differences and Mechanisms

In summary, fluorescence and Raman effect both involve the absorption of photons by molecules and subsequent release of lower energy photons. However, in Raman effect, there is also the possibility of higher frequency photons being released. This is because in fluorescence, the absorption occurs between two electronic states, while in Raman effect it can also occur between vibrational states. The ground state refers to the lowest energy state of the molecule before being excited by incoming photons. It is not possible for a photon to bounce off and have a different frequency.
  • #1
ananthu
106
1

Homework Statement


I understand that in the fluorescence, the incident photon is absorbed by the molecule, and the molecule while returning to its original ground level releases lesser energy. Similarly, in Raman effect also a photon is incident on a liquid molecule. In stokes' lines the lesser frequency is emitted and in the Anti stokes' lines the greater frequency is released. My doubt is: Is the photon completey absorbed by the molecule and the exited molecule gives up a lesser or greater energy in the form of photons (as in the case of fluorescence) or the collided photon itself is simply bounced from the liquid molecule and come out with changed frequencies? In that case what about the energies emitted by the excited molecules themselves while returning to the ground level? Where do they go? Do they also accompany the scattered photons? Also what does a "ground electronic state" exactly stand for? Is it for the K- level of a molecule, ie. the level corresponding to the principal quantum number 1?


Homework Equations





The Attempt at a Solution

 
Physics news on Phys.org
  • #2
Even after several days of posting this question in the forum, I am surprised why I have not got a single reply! Kindly,any one, share your views...
 
  • #3
If the photon is absorbed, it is completely absorbed, since its energy will match the gap between the energy levels of the atom. When the atom falls back to the ground state, it might not do so in one step, but instead it might have several transition states. If so, at each transition, the energy is released as a photon of lesser energy (than the original incident one).

A photon will not bounce off and have a different frequency.

Ground state is the state of lowest energy, before being excited by the incoming photons.
 
  • #4
Thank you for your reply. In one of the texts it is given like this. ie."in fluorescence a photon is completely absorbed whereas it is not so in raman effect". Also in fluoresnce only higher freqency photon is absorbed and the radiation given out is always that of a lower frequency one.. But in raman effect both lower and higher frequencies are given out..
Then how do we exactly differentiate between the two?
Is it that in fluorescence the absorption takes place beteen two real electronic states whereas in the latter the absorption takes place only between vibrational states? So both are the cases of absorptions only?
Is it also possible that an excited atom receives energy from the colliding photon, goes to a higher vibrational state, not an electronic one, returns to the ground state by emitting some infrared lines along with the photon which hit the atom and lost part of its energy? what I mean is that since the infrared emissions can not be seen and therefore we see only the photon bounced with lesser frequency as stokes' line?
 

1. What is the Raman effect?

The Raman effect is a physical phenomenon in which light is scattered by a material, resulting in a shift in the wavelength of the scattered light. This shift is caused by the interaction between the light and the vibrations of the molecules in the material.

2. How is the Raman effect different from fluorescence?

Both the Raman effect and fluorescence involve the interaction of light with a material, but they have different underlying mechanisms. Fluorescence occurs when a material absorbs light of a certain wavelength and then re-emits it at a longer wavelength, while the Raman effect involves a shift in the wavelength of the scattered light due to molecular vibrations.

3. How is the Raman effect used in scientific research?

The Raman effect is used in a variety of scientific fields, including chemistry, physics, and biology. It can be used to identify and characterize unknown materials, study molecular structures and dynamics, and even detect the presence of certain substances in biological samples.

4. What are the limitations of the Raman effect?

One limitation of the Raman effect is that it typically produces a weak signal compared to other spectroscopic techniques, making it less sensitive for detecting low concentrations of substances. Additionally, fluorescence from impurities in a sample can interfere with the Raman signal, making it difficult to accurately interpret the data.

5. How is fluorescence related to Raman spectroscopy?

Fluorescence is often used as a complementary technique to Raman spectroscopy. In some cases, fluorescence can provide additional information about a material that is not readily observable using Raman spectroscopy alone. Additionally, fluorescence can be used to enhance the Raman signal, resulting in a more sensitive and accurate measurement.

Similar threads

  • Quantum Physics
Replies
2
Views
810
Replies
3
Views
802
  • Introductory Physics Homework Help
Replies
6
Views
3K
  • Other Physics Topics
Replies
16
Views
4K
Replies
25
Views
11K
  • Advanced Physics Homework Help
Replies
3
Views
2K
  • Atomic and Condensed Matter
Replies
10
Views
2K
Replies
6
Views
2K
  • Atomic and Condensed Matter
Replies
1
Views
1K
  • Introductory Physics Homework Help
Replies
1
Views
1K
Back
Top