Build a Lightning Cloud with a 555 Timer | LED Flashing Help

  • Thread starter Thread starter Triple_E
  • Start date Start date
  • Tags Tags
    555 timer Timer
AI Thread Summary
The discussion revolves around building a lightning cloud effect using a 555 timer to flash LEDs, but the creator is facing issues with the LED not flashing as intended. Despite checking connections and using various components, the LED either stays on or only lights up when the potentiometer is adjusted to a minimum. Suggestions include using a larger resistor and capacitor to achieve a slower flash rate, ideally 1-2 seconds between flashes. The creator plans to switch to a breadboard for easier troubleshooting and to refine the circuit. Overall, the focus is on achieving the desired LED flashing effect for the project.
Triple_E
Messages
6
Reaction score
0
Hello, I have been in the process of building a small lightning cloud out of Poly-Fil and some LED's. I have looked up on how to build flashing LED's with a 555 timer, and I have tried (many) times, yet every time I hook up the 9v battery, my LED either turns on, but does not flash, or doesn't come on at all until I turn my 10K pot all the way down. I have checked for loose connections, grounding issues, I cannot find any. I have triple and quad checked the diagram. I would really like to be able to use 2-3 lights that fade on and off somewhat quickly, but softly, as to look like lighting. I had bought a 4017 decade timer, in hopes of scattering the lights a little, but first I need to get this 555 to work.

I'm using a 9v battery (I would like to make it a 12v wall wart, if possible)
200uF cap
2n2222 transistor
1K Ohm resistor
400 Ohm for LED (calls for 370, but all I have)
10K Ohm pot to slow the rate of flashing.
(All components are Texas Instruments brand)

PS. I'm not using a breadboard of any kind. I'm (sadly) only able to solder this all together with wires without any kind of good mounting for it. I also bought a 1uf cap for pin 5 but I (stupidly) realized most diagrams call for .1 or even .01.Any kind of help would be immensely helpful! and I appreciate any input!The circuit I'm trying to make. http://www.instructables.com/id/Pulse-Generator-Using-a-555-Timer/?ALLSTEPS
 
Last edited:
Engineering news on Phys.org
Link to diagram for your circuit?
 
You have not included enough information to trouble shoot the problem. Do you have a link to the circuit you are trying to build? If so please post it.
 
Triple_E said:
Hello, I have been in the process of building a small lightning cloud out of Poly-Fil and some LED's. I have looked up on how to build flashing LED's with a 555 timer, and I have tried (many) times, yet every time I hook up the 9v battery, my LED either turns on, but does not flash, or doesn't come on at all until I turn my 10K pot all the way down. I have checked for loose connections, grounding issues, I cannot find any. I have triple and quad checked the diagram. I would really like to be able to use 2-3 lights that fade on and off somewhat quickly, but softly, as to look like lighting. I had bought a 4017 decade timer, in hopes of scattering the lights a little, but first I need to get this 555 to work.

I'm using a 9v battery (I would like to make it a 12v wall wart, if possible)
200uF cap
2n2222 transistor
1K Ohm resistor
400 Ohm for LED (calls for 370, but all I have)
10K Ohm pot to slow the rate of flashing.
(All components are Texas Instruments brand)

PS. I'm not using a breadboard of any kind. I'm (sadly) only able to solder this all together with wires without any kind of good mounting for it. I also bought a 1uf cap for pin 5 but I (stupidly) realized most diagrams call for .1 or even .01.Any kind of help would be immensely helpful! and I appreciate any input!
Hi there
welcome to PF :smile:

none of your info tells us anything about how you wired it up ... chances are your problems are layout/wiring related

firstly, show us your circuit diagram you used
secondly show us some sharp and clear pix of your construction ... clear enough that we can read the text on the componentsDave
 
  • Like
Likes Triple_E
Skyrocket said:
You have not included enough information to trouble shoot the problem. Do you have a link to the circuit you are trying to build? If so please post it.
rootone said:
Link to diagram for your circuit?

Yes! been trying to edit it in for a few. sorry about that.
 
Ok, This is a standard 555 astable oscillator The resistors and cap you are using will cause the LED to flash around 10Hz. This will appear as a fast flicker. This seems a little fast for the effect you seek. First question what strobe rate do you want?
 
Keep in mind, I understand that this is a VERY crude looking circuit I have made and this is not how it should be done (With a piece of sheet plastic) But this is all I have at the moment. But that's beside the point of why I'm not understanding why it is not working.

http://imgur.com/lqRLa29 http://imgur.com/lqRLa29

http://imgur.com/EGY3io2 http://imgur.com/EGY3io2

http://imgur.com/AEpWU4j http://imgur.com/AEpWU4j
 
Last edited by a moderator:
The 555 timer is very tough. I have put together circuits that worked with clip leads. I expect that The LED is flashing just fine, but too fast. What flash rate do you want. Right now, with a 1uf cap and 100kohm resistor the flash rate is 10 times a second.
 
Skyrocket said:
Ok, This is a standard 555 astable oscillator The resistors and cap you are using will cause the LED to flash around 10Hz. This will appear as a fast flicker. This seems a little fast for the effect you seek. First question what strobe rate do you want?

I was hoping for a 1-2 second delay between each flash, if possible. I was going to start with the cap and resistor I have and change them to my liking once I had it working. I have two semi-new PSU's that have anywhere from 100-3.5k uf caps in them (don't know if I can use them though?) I can get resistors as needed from my local electronics shop.

And thank you, sir/ma'am for your help.
 
  • #10
Triple_E said:
I was hoping for a 1-2 second delay between each flash, if possible. I was going to start with the cap and resistor I have and change them to my liking once I had it working. I have two semi-new PSU's that have anywhere from 100-3.5k uf caps in them (don't know if I can use them though?) I can get resistors as needed.

And thank you, sir/ma'am for your help.
Your 100kohm resistor is way too small. If the cap stays the same then the resistor needs to be something larger than 1 meg ohm. At that resistance you may start to have current leakage problems. Try the larger resistor. But a better solution is to increase the cap to 10uf.
 
  • Like
Likes Triple_E
  • #11
Yeah, use the bigger cap, and then use a variable resistor in line with your fixed resistor.
See what works.
 
  • Like
Likes Triple_E
  • #12
You may want to get the circuit working with fixed resistors first. Try using fixed resistors instead of the pot until the circuit works. once it is flashing then you can play with variable resistors to adjust the flash rate.
 
  • Like
Likes Triple_E
  • #14
Okay, I replaced the cap with a 10uf and also replaced the pot with 100k fixed. Although I had noticed that when I had disconnected the battery earlier, the LED stopped coming on at all. Nothing had come loose and/or short circuited that I know of. 555 timer was cool, LED is fine (tested it)
Skyrocket said:
Just for grins. http://www.555-timer-circuits.com/flashing-led.html

Look at the video.

Gahh I wish I had a breadboard right now...haha.
 
  • #15
Triple_E said:
Okay, I replaced the cap with a 10uf and also replaced the pot with 100k fixed. Although I had noticed that when I had disconnected the battery earlier, the LED stopped coming on at all. Nothing had come loose and/or short circuited that I know of. 555 timer was cool, LED is fine (tested it)

Gahh I wish I had a breadboard right now...haha.
Well I looked over the wiring. It is not easy with the black plastic in the way. But I can sort of trace the connections. It looks fine at first glance. This is a standard circuit straight from the manufacturers spec sheet of recommended circuits.
 
  • #16
This is my last post. It is after 11 pm here.
 
  • #17
Skyrocket said:
Well I looked over the wiring. It is not easy with the black plastic in the way. But I can sort of trace the connections. It looks fine at first glance. This is a standard circuit straight from the manufacturers spec sheet of recommended circuits.

I have done the same a dozen times, on half dozen different diagrams. Obviously the way I'm building these are wrong. The way I'm seeing the diagram or something. I'm going to be able to get a breadboard today, so I'm just going to get it to work on one of those and work from there.

I really appreciate your time trying to help me.
 

Similar threads

Making a Blinking LED 555 Timer
Replies
6
Views
4K
Request help with 555 timer circuit
Replies
9
Views
9K
Troubleshooting a 555 Timer Circuit with Added LEDs | Circuit Issues & Solutions
Replies
5
Views
3K
Help with 555 Timer Chip & 38 kHz IR Light
Replies
8
Views
6K
Using a 555 timer as an analog frequency divider?
Replies
3
Views
8K
555 timer strobe light not working
Replies
11
Views
5K
Troubleshooting 555 Timer Circuits
Replies
6
Views
11K
Help Needed: Heart-Shaped Badge w/ 8 LEDs & ICs 4017/555 Timer
Replies
17
Views
4K
Why is my 555 Timer not blinking?
3
Replies
107
Views
29K
Using multiple 555 timers in astable
Replies
5
Views
9K

Hot Threads

Recent Insights

Back
Top