Calculating Kinetic Energy with P=1/2Aρv3

AI Thread Summary
The formula P = 1/2 Aρv^3 is used to calculate power, where P is indeed in watts. The variables represent area (A in m²), density (ρ in kg/m³), and velocity (v in m/s). A participant confirmed that using metric units is essential for accurate calculations. The original poster, Rick, initially used non-metric units but acknowledged the need to convert them. Ensuring proper unit conversion is crucial for correct kinetic energy calculations.
rickeeee
Messages
2
Reaction score
0
Hi Everyone,
This is a real simple question, but I should make sure I have this right. In the following formula, is the value of P in watts?

P = 1/2 Aρv3

I'm assuming that this is in watts, but you know what they say about assuming. Thanks in advance for your help!
Cheers,
Rick
 
Physics news on Phys.org
Assuming ρ is in [kg/m3] and v is in [m/s] and A is in [m2], then yes P is in watts.
 
Hello MrMatt,
Thank you very much, I was using Slugs for ρ and A was equal to FT2, but I can convert them to metrics. Glad I double checked!
Cheers,
Rick
 

Thread 'Average velocity as a weighted mean'

Hello everyone, Consider the problem in which a car is told to travel at 30 km/h for L kilometers and then at 60 km/h for another L kilometers. Next, you are asked to determine the average speed. My question is: although we know that the average speed in this case is the harmonic mean of the two speeds, is it also possible to state that the average speed over this 2L-kilometer stretch can be obtained as a weighted average of the two speeds? Best regards, DaTario
View full post »

Thread '1:1 versus 2:1 Mechanical Advantage debate'

The rope is tied into the person (the load of 200 pounds) and the rope goes up from the person to a fixed pulley and back down to his hands. He hauls the rope to suspend himself in the air. What is the mechanical advantage of the system? The person will indeed only have to lift half of his body weight (roughly 100 pounds) because he now lessened the load by that same amount. This APPEARS to be a 2:1 because he can hold himself with half the force, but my question is: is that mechanical...
View full post »
Thread 'Beam on an inclined plane'

Thread 'Beam on an inclined plane'

Hello! I have a question regarding a beam on an inclined plane. I was considering a beam resting on two supports attached to an inclined plane. I was almost sure that the lower support must be more loaded. My imagination about this problem is shown in the picture below. Here is how I wrote the condition of equilibrium forces: $$ \begin{cases} F_{g\parallel}=F_{t1}+F_{t2}, \\ F_{g\perp}=F_{r1}+F_{r2} \end{cases}. $$ On the other hand...
View full post »

Similar threads

I Kinetic Energy derivation assumption?
Replies
11
Views
2K
B About verification on Kinetic energy and work
Replies
16
Views
2K
I am confused about the meaning, and value, of kinetic energy
Replies
7
Views
2K
B Colliding balls: Conservation of momentum and changes in kinetic energy?
Replies
2
Views
2K
I Question about Momentum vs. Kinetic Energy vs. Deforming In Collisions
Replies
2
Views
2K
Confusion about tidal locking and rotational kinetic energy
Replies
3
Views
2K
Formulating the kinetic energy of an object - helical motion
Replies
9
Views
3K
I Change of coordinates in a potential energy field
Replies
2
Views
1K
Average kinetic energy in 1 dimension according to the M-B Distribution
Replies
18
Views
3K
Help me find my error in a relativistic kinetic energy calculation
Replies
9
Views
3K

Hot Threads

Recent Insights

Back
Top