How to Disconnect a Car Battery at 11.8V Using an Adjustable Voltmeter?

  • Thread starter Thread starter trulka
  • Start date Start date
Click For Summary

Discussion Overview

The discussion revolves around the challenge of disconnecting a car battery at a specific voltage (11.8V) while building an electric racecar. Participants explore various methods and components that could be used to achieve this goal, including the use of adjustable voltmeters and voltage detector chips.

Discussion Character

  • Exploratory
  • Technical explanation
  • Debate/contested

Main Points Raised

  • Tom expresses the need to disconnect a car battery at 11.8V and seeks advice on using an adjustable voltmeter or detector.
  • Warren questions the feasibility of using only one 12V battery at a time for a racecar, suggesting that the power output is insufficient.
  • Some participants mention the availability of battery voltage detector chips from manufacturers like Maxim, suggesting their use in conjunction with power MOSFETs.
  • One participant proposes a warning system using a diode and resistor combination to switch at 11.8V.
  • There is a side discussion about the phrase "then bob's your uncle," with participants providing historical context and clarification of its meaning.
  • Another participant seeks clarification on whether both batteries will be present in the car simultaneously and questions how to demonstrate that only one battery is used at a time for contest purposes.

Areas of Agreement / Disagreement

Participants express differing views on the practicality of using a single battery for the racecar, with some supporting the idea of switching batteries while others question its viability. The discussion remains unresolved regarding the best approach to disconnect the battery at the specified voltage.

Contextual Notes

There are assumptions about the power requirements for the racecar and the effectiveness of proposed solutions, which remain unverified. The discussion includes informal exchanges that may not directly relate to the technical aspects of the original question.

trulka
Messages
1
Reaction score
0
Hey guys,

I am building an electric racecar for university and I'm stuck!. It has to be run on car batteries and it can only use one at a time... many people are just using an excellent battery with a great amp-hour rating... but I'd like to switch batteries halfway through...

I want to disconnect a car battery when it reaches 11.8V and possibly using an adjustable voltmeter/detector?

Please help, any advice would be great!

Thank you!
-Tom
 
Engineering news on Phys.org
You're not going to build much of a race car with only one 12V battery at a time. A single 12V battery, even at 100 amperes of current, is only providing 1,200 watts of power. This is about the same amount of power generated by a lawnmower engine.

- Warren
 
There are plenty of battery voltage detector chips about.

Maxim make a shedload.

Combined with suitably zonky Power mosfets, then bob's yer uncle.
 
zeitghost said:
Maxim make a shedload.

Combined with suitably zonky Power mosfets, then bob's yer uncle.

You Brits sure talk funny :smile:
 
berkeman said:
You Brits sure talk funny :smile:

We've had centuries to practice... :biggrin:

Zonky, by the by, means "large" as in >100A Id(on).
 
One way for a warning system would be to setup a diode with a resistor (or trim pot) combination that switches at 11.8V.
 
What the heck does "then bob's your uncle" mean?

CS
 
stewartcs said:
What the heck does "then bob's your uncle" mean?
It means you're problems are solved

Historical note:
Robert Gascoyne-Cecil,was prime minister in the 1890 and was a big fan of nepotism - appointing his nephew as minister, so if Robert (bob) was your uncle you didn't have any problems getting a job.

Interestingly neptosim is from the Italian for nephew and comes from Pope's giving appointments to their (cough) nephews (cough)
 
mgb_phys said:
It means you're problems are solved

Historical note:
Robert Gascoyne-Cecil,was prime minister in the 1890 and was a big fan of nepotism - appointing his nephew as minister, so if Robert (bob) was your uncle you didn't have any problems getting a job.

Interestingly neptosim is from the Italian for nephew and comes from Pope's giving appointments to their (cough) nephews (cough)

Ah...Thanks.

CS
 
  • #11
trulka said:
I want to disconnect a car battery when it reaches 11.8V and possibly using an adjustable voltmeter/detector?

Do I understand that both batteries will be in the car at all times, and you want a circuit that electrically switches over to battery #2 when battery #1 reaches 11.8V?

If this is for a contest, how will you convince the judges that only one battery is being used at a time?
 

Similar threads

  • · Replies 5 ·
Replies
5
Views
3K
Replies
7
Views
4K
  • · Replies 7 ·
Replies
7
Views
2K
Replies
24
Views
4K
  • · Replies 1 ·
Replies
1
Views
4K
  • · Replies 10 ·
Replies
10
Views
2K
Replies
1
Views
4K
  • · Replies 4 ·
Replies
4
Views
4K
  • · Replies 28 ·
Replies
28
Views
5K
Replies
3
Views
2K